《ISO-2705-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-2705-2006.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 2705:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 2705 Sixth edition 2006-10-01 Road vehicles M12 x 1,25 spark-plugs with flat seating and their cylinder head housings Vhicules routiers Bougies dallumage M12 1,25 sige plat et leurs logements dans la culasse ISO 2705:2006(E) PDF
2、disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, part
3、ies accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative
4、to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 A
5、ll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country
6、 of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved -,-,- ISO 2705:2006(E) ISO 2006 All rights reserved iii Foreword ISO (the Internatio
7、nal Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been
8、established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standar
9、dization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for v
10、oting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all s
11、uch patent rights. ISO 2705 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 1, Ignition equipment. This sixth edition cancels and replaces the fifth edition (ISO 2705:1999), which has been technically revised. -,-,- INTERNATIONAL STANDARD ISO 2705:2006(E) ISO 2006 All r
12、ights reserved 1 Road vehicles M12 1,25 spark-plugs with flat seating and their cylinder head housings 1 Scope This International Standard specifies characteristics of M12 1,25 spark-plugs with flat seating and their cylinder head housings, for use with spark-ignition engines. 2 Normative references
13、 The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 68-1, ISO general purpose screw threads Basi
14、c profile Part 1: Metric screw threads ISO 261, ISO general purpose metric screw threads General plan ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional
15、threads ISO 14508, Road vehicles Spark-plugs Terminals 3 Terminals The spark-plug terminal may be either the solid post or the threaded type as specified in ISO 14508. A spark-plug with threaded terminal on which a nut is applied shall respect the dimensions specified for spark-plugs with solid post
16、 terminals (see Figures 1 and 2). 4 Dimensions and threads 4.1 Spark-plug reach The spark-plug reach shall be according to Table 1 (see Figures 1 to 4). -,-,- ISO 2705:2006(E) 2 ISO 2006 All rights reserved Table 1 Spark-plug reach Dimensions in millimetres A E a Type of reach Tolerance of A + E: 0,
17、2 B max. Y + 0,3 0,8 Normal 12,7 21 11,7 Long 0 27 Extended long 19 1,5 6 31 18 Extra long 0 34,5 Extended extra long 26,5 1,5 6 38,5 25,5 a It is intended to specify E more definitively in future revisions of this International Standard. 4.2 Gasket When the spark-plugs have been tightened with a to
18、rque of 25 Nm, on threads that are clean, smooth and dry, the gaskets shall be 1 mm to 1,6 mm thick. If the gasket thicknesses are different, a corresponding adjustment to dimensions A, B and Y shall be made. Non-captive gaskets may be used in special cases. 4.3 Threads for spark-plugs and cylinder
19、heads 4.3.1 General The threads of M12 1,25 spark-plugs and the corresponding tapped holes in the cylinder head shall conform to ISO 68-1, ISO 261, ISO 965-1 and ISO 965-3. Their limiting dimensions and their tolerance classes are specified in 4.3.2 and 4.3.3 respectively. 4.3.2 Limiting dimensions
20、The limiting dimensions are given in Table 2. Table 2 Limiting dimensions Dimensions in millimetres Dimension Plug thread (on finished plug) Tapped hole in cylinder head max. 11,937 not specified Major diameter min. 11,725 12,000 max. 11,125 11,368 Pitch diameter min. 10,993 11,188 max. 10,404 10,91
21、2 Minor diameter min. 10,181 a 10,647 a With a root radius W 0,125 mm (0,1 P). ISO 2705:2006(E) ISO 2006 All rights reserved 3 4.3.3 Tolerance classes The thread tolerance classes of finished M12 1,25 spark-plugs and of the corresponding tapped holes in the cylinder head are as follows: 6e for spark
22、-plugs (see Note 1); 6H for tapped holes in the cylinder head. NOTE 1 In order that spark-plugs complying with this International Standard can be fitted in existing cylinder heads, also in extreme cases, the value for the maximum truncation of the minor diameter of the spark-plug base has been sligh
23、tly reduced with respect to the ISO value. This maximum value of the minor diameter is calculated from a distance of H/6 for the maximum truncation instead of the value given by the formula in ISO 965-1, according to the formula given below: Minor diameter, maximum = d1 es 2(H/4 H/6) = (10,647 0,063
24、 0,180) mm = (10,647 0,243 = 10,404) mm The value for the basic profile remains the same as for the ISO thread (10,647 0,063 = 10,584) mm. NOTE 2 The initial clearance e = 0,063 mm between the pitch diameters of the thread and of the tapped hole is intended to prevent the possibility of seizure, as
25、a result of combustion deposits on the bare threads, when removing the spark-plugs. This clearance is also intended to enable spark-plugs with threads in accordance with this International Standard to be fitted in existing tapped holes. 5 Other dimensions of spark-plugs and their cylinder head housi
26、ngs The other dimensions shall be as indicated in Figures 1 to 5. Dimensions 52,5 mm on spark-plugs with solid post terminal and 49,5 mm on spark-plugs with threaded terminal shall be measured when the spark-plugs have been tightened according to 4.2. The non-ribbed insulator design is preferred bec
27、ause it provides superior protection to flashover between the spark-plug insulator and the cover. The Z length of the spark-plug housing in the cylinder head shall be sufficient to ensure that the end of the spark-plug thread does not project into the combustion chamber at any point when the gasket
28、is tightened to its maximum specified torque. Details not specified are left to the manufacturers choice. -,-,- ISO 2705:2006(E) 4 ISO 2006 All rights reserved Dimensions in millimetres Key 1 solid terminal (ISO 14508) 2 captive gasket 3 pitch diameter a Dimension after spark-plug has been tightened
29、 with a torque of 25 Nm. b Optional. c Dimension B is the maximum protrusion of any part of the spark-plug into the combustion chamber. Figure 1 Spark-plug with solid post terminal (preferred design with non-ribbed insulator) Dimension in millimetres a The number and shape of ribs are optional. Figu
30、re 2 Spark-plug with solid post terminal (traditional design with ribbed insulator) -,-,- ISO 2705:2006(E) ISO 2006 All rights reserved 5 Dimension in millimetres Key 1 threaded terminal (ISO 14508) 2 captive gasket 3 pitch diameter a Dimension after spark-plug has been tightened with a torque of 25
31、 Nm. b Optional. c Dimension B is the maximum protrusion of any part of the spark-plug into the combustion chamber. Figure 3 Spark-plug with threaded terminal (preferred design with non-ribbed insulator) Dimension in millimetres a The number and shape of ribs are optional. Figure 4 Spark-plug with t
32、hreaded terminal (traditional design with ribbed insulator) ISO 2705:2006(E) 6 ISO 2006 All rights reserved Dimension in millimetres a Engine manufactures are encouraged to use a value of u 3 mm instead of u 5 mm for new engine designs. Figure 5 Housing of spark-plug in cylinder head 6 Installation
33、tightening torque The installation torque values apply to new spark-plugs without lubricant on the threads. If threads are lubricated, the torque value shall be reduced by approximately one-third to avoid overstressing. Spark-plugs shall be tightened with a torque of 15 Nm to 25 Nm. NOTE Engine manufacturers may specify a different torque for the first spark-plug installation. -,-,- -,-,- ISO 2705:2006(E) ICS 43.060.50 Price based on 6 pages ISO 2006 All rights reserved -,-,-
链接地址:https://www.31doc.com/p-3778619.html