《ISO-3547-6-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-3547-6-2007.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 3547-6:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 3547-6 First edition 2007-10-01 Plain bearings Wrapped bushes Part 6: Checking the inside diameter Paliers lisses Bagues roules Partie 6: Contrle du diamtre intrieur Copyright International Organization for Standardization Prov
2、ided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Ado
3、bes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy
4、. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every car
5、e has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no
6、 part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case posta
7、le 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, Use
8、r=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references. 1 3 Symbols and units 2 4 Method of checking 2 5 Test equipme
9、nt . 2 6 Procedure 6 Bibliography. 7 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO
10、3547-6:2007(E) iv ISO 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each me
11、mber body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Inter- national
12、 Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted according to the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopte
13、d by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
14、 rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3547-6 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 5, Quality analysis and assurance. This part of ISO 3547 cancels and replaces ISO 12307-2:2000, which has been technica
15、lly revised. ISO 3547 consists of the following parts, under the general title Plain bearings Wrapped bushes: Part 1: Dimensions Part 2: Test data for outside and inside diameters Part 3: Lubrication holes, grooves and indentations Part 4: Materials Part 5: Checking the outside diameter Part 6: Chec
16、king the inside diameter Part 7: Measurement of wall thickness of thin-walled bushes Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networki
17、ng permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 3547-6:2007(E) ISO 2007 All rights reserved 1 Plain bearings Wrapped bushes Part 6: Checking the inside diameter 1 Scope The part of ISO 3547 specifies, following ISO 12301, the checking of the inside diameter of wrapped bushes (
18、see ISO 3547-2:2006, method C) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the housing bore due to the interference between the outside diameter of the bush and the hou
19、sing bore. NOTE 1 All dimensions in this part of ISO 3547 are given in millimetres except where otherwise noted/designated. NOTE 2 The dimensions and tolerances of wrapped bushes are given in ISO 3547-1. NOTE 3 Checking of the wall thickness is the subject of ISO 3547-7. NOTE 4 Checking of the outsi
20、de diameter of wrapped bushes is the subject of ISO 3547-5. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (i
21、ncluding any amendments) applies. ISO 3547-1:2006, Plain bearings Wrapped bushes Part 1: Dimensions Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduct
22、ion or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) 2 ISO 2007 All rights reserved 3 Symbols and units See Table 1. Table 1 Symbols and units Symbol Parameter Unit B Nominal width of the bush millimetres bch, 1 Width of the ring gauge millimetres bch, 2 Width of the plug ga
23、uge millimetres d0 Outside diameter of the ring gauge millimetres Di Nominal inside diameter of the bush millimetres Di, ch Inside diameter of the bush in the ring gauge millimetres Do Nominal outside diameter of the bush millimetres Ra Surface roughness micrometres t1 Tolerance of form and position
24、 millimetres dch, 1 Inside diameter of the ring gauge millimetres dch, 2 Outside diameter of the plug gauge millimetres 4 Method of checking The free diameter of a wrapped bush is not measured directly because of the flexible nature of the components. To check the inside diameter, Di, ch, the bush i
25、s pressed into a ring gauge whose nominal diameter corresponds to the dimension of the housing. For bushes specified in ISO 3547-1, the tolerance class of housing bore is normally H7. When the bush is pressed into the ring gauge, it is possible that there is a permanent reduction in the outside diam
26、eter. The inside diameter, Di, ch, is measured with a three-point measuring instrument or with a GO or a NO GO gauge. In order to enable the supplier and the user to compare results of this test it shall be agreed whether results shall be obtained by measuring or by gauging. 5 Test equipment 5.1 Rin
27、g gauge Unless otherwise agreed between supplier and user, the dimensions shown in Figure 1 and given in Table 2 are valid for the ring gauge. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for
28、Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) ISO 2007 All rights reserved 3 Dimensions in millimetres, unless otherwise designated a bch, 1 W B + 9 b do W dch, 1 + 50 Figure 1 Ring gauge Table 2 Dimensions, manufacturing tol
29、erances and wear limits for ring gauges and plug gauges Dimensions in millimetres Doa nominal dch, 1 dch, 2 t1 Target Sizeb Manufacturing tolerance Wear limit Manufacturing tolerance Wear limit Manufacturing tolerance Wear limit u 10 Do + 0,008 10 u 18 Do + 0,009 18 u 30 Do + 0,011 30 u 50 Do + 0,01
30、3 50 u 80 Do + 0,015 80 u 120 Do + 0,018 0,003 0 + 0,005 0 + 0 0,003 0,005 0,002 0,004 120 u 180 Do + 0,020 0,005 0 + +0,007 0 0,005 0,007 0,003 0,005 a For bushes with Do 180 mm, agreement shall be reached between the supplier and user. b The target size of the ring gauge inside diameter is made up
31、 of Do and the rounded average value of the tolerance class H7. In ISO 3547-1, H7 is recommended as the tolerance class for the housing bore. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for R
32、esale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) 4 ISO 2007 All rights reserved 5.2 Plug gauge Unless otherwise agreed between supplier and user, the following dimensions are valid for the plug gauge (see Figures 2 and 3 and Tabl
33、e 2). The nominal plug gauge diameter can be obtained from Table 4 in ISO 3547-1:2006. Key 1 field for marking a bch, 2 W B + 5 Figure 2 Plug gauge, solid, for dch, 2 u 80 mm Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/111111
34、1001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) ISO 2007 All rights reserved 5 Dimensions in millimetres, unless otherwise designated Key 1 field for marking a bch, 2 W B + 5 Figure 3 Plug gauge,
35、 example with blind hole, for dch, 2 80 mm 5.3 Three-point measuring instrument Measures are made in the radial direction using the spherical faces of the measuring pins shown in Figure 4. Figure 4 Three-point measuring instrument Copyright International Organization for Standardization Provided by
36、IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) 6 ISO 2007 All rights reserved 5.4 Requirements for measuring equipment The ring gauge and
37、plug gauge shall be from hardened (60 HRC to 64 HRC) and non-ageing steel. 5.5 Measuring errors Frequent measuring errors are as follows. a) Ring gauge and plug gauge are damaged or worn. b) Ring gauge and plug gauge have no lead-in chamfer. c) Bush is misaligned when introduced into the ring gauge.
38、 d) Plug gauge is misaligned when introduced into the bush. e) Width of the ring gauge is less than the width of the bush. f) Grease, dirt, damages, burrs and swelling are present around features on the bush and test equipment. 6 Procedure The bush shall be introduced into the ring gauge from that s
39、ide having the lead-in chamfer. Subsequently, the inside diameter shall be determined by means of a) the three-point measuring instrument; b) the GO plug gauge (see Figures 2 and 3), which shall be inserted with minimum effort; the NO-GO plug gauge, which shall not be able to be inserted manually wi
40、th a maximum force of 250 N. Where it is necessary to limit the maximum force, it shall be agreed between supplier and user. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007
41、 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) ISO 2007 All rights reserved 7 Bibliography 1 ISO 3547-2:2006, Plain bearings Wrapped bushes Part 2: Test data for outside and inside diameters 2 ISO 3547-5, Plain bearings Wrapped bushes Part 5: C
42、hecking the outside diameter 3 ISO 3547-7, Plain bearings Wrapped bushes Part 7: Measurement of wall thickness of thin-walled bushes 4 ISO 12301, Plain bearings Quality control techniques and inspection of geometrical and material quality characteristics Copyright International Organization for Stan
43、dardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 3547-6:2007(E) ICS 21.100.10 Price based on 7 pages ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 10/17/2007 05:14:24 MDTNo reproduction or networking permitted without license from IHS -,-,-
链接地址:https://www.31doc.com/p-3779030.html