《ISO-8116-3-1995.pdf》由会员分享,可在线阅读,更多相关《ISO-8116-3-1995.pdf(12页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 8116-3 Second edition 1995-09-15 Textile machinery and accessories - Beams for winding - Part 3: Weaver s beams Materie1 pour I industrie textile - Ensouples pour enroulement - Partie 3: Ensouples de tissage Reference number ISO 8116-3:1995(E) Copyright International Organ
2、ization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 8116=3:1995(E) Foreword ISO (the International Organization for Standard
3、ization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to
4、be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International
5、 Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 8116-3 was prepared by Technical Committee lSO/TC 72, Textile mac
6、hinery and allied machinery and accessories, Sub- committee SC 2, Winding and preparatory machinery for fabric manufac- ture. This second edition of ISO 8116-3 cancels and replaces ISO 6175:1983 and ISO 8116-3:1986, which have been technically revised. ISO 8116 consists of the following Parts, under
7、 the general title Textile machinery and accessories - Beams for winding: - Part 7: General vocabulary - Part 2: Warpe0 beams - Part 3: Weaver s beams - Part 4: Quality classification of flanges for weaver s beams, warper s beams and sectional beams - Part 5: Sectional beams for Warp knitting machin
8、es - Part 6: Beams for ribbon weaving and ribbon knitting - Part 7: Beams for dyeing slivers, rovings and yarns 0 ISO 1995 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronie or mechanical, including photo
9、copying and microfilm, without Permission in writing from the publisher. International Organization for Standardization Case Postale 56 l CH-l 211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO License
10、e=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- 0 ISO ISO 8116=3:1995(E) - Part 8: Definitions of run-out tolerantes and methods of measure- ment - Part 9: Dyeing beams for textile fabrics Copyright
11、 International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- This page intentionally left blank Copyright Internation
12、al Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD 0 ISO ISO 8116=3:1995(E) Textile machinery an
13、d accessories - Beams for winding - Part 3: Weaver s beams 1 Scope This part of ISO 8116 defines the basic terms and lays down the main dimensions and the variations in form and Position for weaver s beams that are used for weaving preparation as weil as for weaving. Furthermore the main dimensions
14、of the Profile threads for weaver s beams are given. 2 Normative references The following Standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 8116. At the time of publication, the editions indicated were valid. All Standards are subject to re
15、vision, and Parties to agreements based on this part of ISO 8116 are encouraged to investigate the possibility of applying the most recent editions of the Standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 109: 1982, Textile machinery
16、 - Working widths of weaving machines. ISO 286-2: 1988, ISO s ystem of limits and fits - Part 2: Tables of Standard tolerante grades and limit deviations for holes and shafts. ISO 8116-8: 1995, Textile machinery and accessories - Beams for winding - Part 8: Definitions of run-out toler- ances and me
17、thods of measurement. 3 Terminology and main dimensions (See figures 1 and 2 and table 1) d, flange diameter L I 1 c Figure 3 - Type 1 threads Dimensions in millimetres - Flange /- Barrel Figure 4 - Type 2 threads Copyright International Organization for Standardization Provided by IHS under license
18、 with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 8116=3:1995(E Table 2 - Type 1 threads Dimensions tn millimetres 4 4 0 4 +0,15 -0,2 0 I 150 149,35 147,45 216 215,35 213,45 269 2
19、68,35 266,45 Table 3 - Type 2 threads Dimensions in millimetres 4 4 0 d7 +0,15 -0,l 0 150 149,9 149,2 216 215,9 215,2 269 268,9 268,2 NOTE - Threads of type 2 are primarily used as adjusting threads. Flanges are usually secured to the barrel by separate means. 5 Circular axial rumout tolerante, Ta,
20、of flanges The permissible circular axial run-out tolerantes, Ta, of the flanges are given in table4. The run-out shall be measured in accordance with ISO 8116-8. Table 4 - Permissible circular axial run-out of flanges 6 Total rumout tolerante, T, of the barrel The permissible total run-out tolerant
21、e, T, of the barrel is given in millimetres, by the formula Tr = 0,25 x I, 1 000 The run-out shall be measured in accordance with ISO 8116-8. 5 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resal
22、e, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 8116-3:1995(E) 7 Other specifications The following details should be specified as appropriate: a) materials of barrel, end plates and flanges; W d d) d nature of material to be wound; surface finish
23、 of the inner sides of the flanges and the exterior surface of the barrel; end plates with shafts on both sides as an alternative to the use of different shaft diameters; fastening of the end plates on the barrel; holes in the barrel for fastening the warp (care should be taken when winding highly e
24、lastic yarns, as holes fastening the warp Cause a weakening of the Cross-section of the barrel); for g) designs of flanges; hl i) fastening of the flanges on the barrel; maximum and minimum lengths of barrel between flanges (“dress width”); j) driving hole in the barrel; k) use of ruffles. For Stand
25、ard working widths of weaving machines, see ISO 109. 8 Designation The designation of a weaver s beam in accordance with this part of ISO 8116 shall include the following infor- mation in the Order given: a) “Weaver s beams”; b) reference to this part of ISO 8116, i.e. ISO 8116-3; c) the type of bea
26、m (A or B); d) d the flange diameter, d, in millimetres; the shaft diameter, 4, in millimetres; f) the barrel length, Z, in millimetres. EXAMPLE A weaver s beam, type A, with a flange diameter d, of 800 mm, shaft diameter 4 of 38 mm and barrel length I, of 1 800 mm shall be designated as follows: We
27、aver s beam ISO 8116-3 - A 800 x 38 x 1800 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- This
28、 page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 8116-3:1995(
29、E) ICS 59.120.20 Descriptors: textile machinery, winding, yarns, beams (textile machinery), basic concepts, dimensions, run-out tolerantes, designation. Price based on 6 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 20:57:45 MDTNo reproduction or networking permitted without license from IHS -,-,-
链接地址:https://www.31doc.com/p-3779143.html