ISO-6597-2005.pdf
《ISO-6597-2005.pdf》由会员分享,可在线阅读,更多相关《ISO-6597-2005.pdf(52页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 6597:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 6597 Fourth edition 2005-07-01 Road vehicles Hydraulic braking systems, including those with electronic control functions, for motor vehicles Test procedures Vhicules routiers Systmes de freinage hydraulique, y compris ceux fonct
2、ion de commande lectronique, pour vhicules moteur Modes opratoires dessai ISO 6597:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are l
3、icensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details o
4、f the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relati
5、ng to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, withou
6、t permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All right
7、s reserved ISO 6597:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 Symbols. 4 5 Test site conditions 5 5.1 Road conditions 5 5.2 Test area for vehicles with an anti-lock braking function (ABS) . 5 5.3 Ambient cond
8、itions 6 6 General information 6 7 Preliminary comments on test procedures and requirements 6 8 Recommended test order 8 Annex A (normative) Pre-test phase and static tests. 10 Annex B (normative) Basic performance test Unladen. 15 Annex C (normative) Failure test Unladen 17 Annex D (normative) ABS
9、function tests with the vehicle unladen 22 Annex E (normative) ABS function tests with the vehicle laden 27 Annex F (normative) Failure test Laden 31 Annex G (normative) Basic performance test Laden. 33 Annex H (normative) Special test. 41 Annex I (normative) Braking systems with energy assistance T
10、ests for vehicles with vacuum or hydraulic boosters or full power braking systems. 42 -,-,- ISO 6597:2005(E) iv ISO 2005 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepa
11、ring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in l
12、iaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task o
13、f technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention i
14、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6597 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 2, Braking systems and eq
15、uipment. This fourth edition cancels and replaces the third edition (ISO 6597:2002), which has been technically revised. This fourth edition incorporates the relevant portions of the International Standard ISO 11835: “Road Vehicles- Motor vehicles. Measurement of braking performance under ABS operat
16、ion” for testing vehicles which are fitted with anti lock function. -,-,- INTERNATIONAL STANDARD ISO 6597:2005(E) ISO 2005 All rights reserved 1 Road vehicles Hydraulic braking systems, including those with electronic control functions, for motor vehicles Test procedures 1 Scope This International S
17、tandard specifies the method of testing the hydraulic braking systems of vehicles of categories M and N which are built to comply with ECE-R 13/09, including supplements 1 to 7. The values in square brackets are taken from ECE Regulation No. 13 for information. Hydraulic braking systems include vacu
18、um-assisted and power hydraulic-assisted braking systems as well as full power hydraulic braking systems. NOTE Test methods covering the Electrical Regenerative Braking Systems of Electrical and Hybrid Vehicles are not included in this edition. This omission may be corrected by a further annex once
19、these vehicles are in more common use and suitable practical test methods have been developed. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest ed
20、ition of the referenced document (including any amendments) applies. ECE Regulation No. 13, Uniform provisions concerning the approval of vehicles with regard to braking, incorporating the 09 series of amendments including supplements 1 to 7 ECE R.E.3, Consolidated Resolution on the Construction of
21、Vehicles 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 vehicle categories as defined in ECE R.E.3 3.1.1 category M power-driven vehicles having at least four wheels and used for the carriage of passengers 3.1.2 category N power-driven vehic
22、les having at least four wheels and used for carriage of goods 3.2 categories of anti-lock braking function (ABS) as defined in ECE Regulation No. 13, Annex 13 ISO 6597:2005(E) 2 ISO 2005 All rights reserved 3.2.1 category 1 that which meets all the requirements of ECE R 13, Annex 13 3.2.2 category
23、2 that which meets all the requirements of ECE R 13, Annex 13 except paragraph 5.3.5. NOTE No braking rate on split-adhesion surfaces is prescribed. 3.2.3 category 3 that which meets all the requirements of ECE R 13, Annex 13 except paragraphs 5.3.4 and 5.3.5 NOTE All split-adhesion tests are omitte
24、d. 3.3 vehicle loading 3.3.1 laden vehicle vehicle laden to its maximum technically permissible mass Mmax as specified by the vehicle manufacturer and acknowledged by the Technical Services NOTE This mass may exceed the “maximum authorized total mass” permitted by national regulations. Mass distribu
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 6597 2005
链接地址:https://www.31doc.com/p-3779145.html