ISO-7617-2-2003.pdf
《ISO-7617-2-2003.pdf》由会员分享,可在线阅读,更多相关《ISO-7617-2-2003.pdf(14页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 7617-2 Third edition 2003-08-01 Reference number ISO 7617-2:2003(E) ISO 2003 Plastics-coated fabrics for upholstery Part 2: Specification for PVC-coated woven fabrics Supports textiles revtus de plastique pour ameublement et garniture Partie 2: Spcifications pour les tissu
2、s revtus de PVC ISO 7617-2:2003(E) ii ISO 2003 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed
3、 on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products
4、used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, pleas
5、e inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing
6、from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 7617-2:2003(E) ISO 2003 All rights reserv
7、ed iii Contents Page 1Scope 1 2Normative references 1 3Technical requirements . 1 4Sampling . 2 5Testing and compliance 2 6Marking . 3 Annex A (normative) Method of selecting test specimens . 4 Annex B (normative) Determination of resistance to print wear . 6 Annex C (normative) Determination of col
8、our fastness to rubbing 8 -,-,- ISO 7617-2:2003(E) iv ISO 2003 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out throu
9、gh ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collabora
10、tes closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standar
11、ds. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of th
12、is document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7617-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses). This third edition cancels and repla
13、ces the second edition (ISO 7617-2:1994), which has been technically revised. ISO 7617 consists of the following parts, under the general title Plastics-coated fabrics for upholstery: Part 1: Specification for PVC-coated knitted fabrics Part 2: Specification for PVC-coated woven fabrics Part 3: Spec
14、ification for polyurethane-coated woven fabrics -,-,- INTERNATIONAL STANDARDISO 7617-2:2003(E) ISO 2003 All rights reserved 1 Plastics-coated fabrics for upholstery Part 2: Specification for PVC-coated woven fabrics 1Scope This part of ISO 7617 specifies requirements for coated fabrics for upholster
15、ed furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings are known as poly(vinyl chloride) (PVC) coatings. The present spe
16、cification covers two grades (A and B) of PVC-coated woven fabric. 2Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docum
17、ent (including any amendments) applies. ISO 105-A02:1993, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour ISO 105-B01:1994, Textiles Tests for colour fastness Part B01: Colour fastness to light: Daylight ISO 105-B02:1994, Textiles Tests for colour fastness Part
18、 B02: Colour fastness to artificial light: Xenon arc fading lamp test ISO 105-X12:2001, Textiles Tests for colour fastness Part X12: Colour fastness to rubbing ISO 176:1976, Plastics Determination of loss of plasticizers Activated carbon method ISO 1421:1998, Rubber- or plastics-coated fabrics Deter
19、mination of tensile strength and elongation at break ISO 2231:1989, Rubber- or plastics-coated fabrics Standard atmospheres for conditioning and testing ISO 2286-1:1998, Rubber- or plastics-coated fabrics Determination of roll characteristics Part 1: Methods for determination of length, width and ne
20、t mass ISO 2411:2000, Rubber- or plastics-coated fabrics Determination of coating adhesion ISO 4674-1:2003, Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods ISO 5978:1990, Rubber- or plastics-coated fabrics Determination of blocking resistance
21、 ISO 7854:1995, Rubber- or plastics-coated fabrics Determination of resistance to damage by flexing 3Technical requirements 3.1Physical requirements The material shall comply with the appropriate requirements of Table 1. -,-,- ISO 7617-2:2003(E) 2 ISO 2003 All rights reserved 3.2Colour fastness requ
22、irements The material shall comply with the requirements of Table 2. 3.3Visual examination The coating of the material shall be uniformly applied and shall be free from visible flaws and cracks and when viewed under a magnification of shall be substantially free from pinholes. The base fabric, unles
23、s coated with an unpigmented coating, shall not be visible when viewed from the coated side. 3.4Colour, grain and finish The colour, grain and finish of the material, whether in single-colour or multicolour effects, shall be agreed between the purchaser and the supplier. Colours shall be compared un
24、der the conditions stipulated in ISO 105-B01. 3.5Width of material The usable width of material when measured in accordance with ISO 2286-1 shall be as agreed between the purchaser and the supplier. For this purpose, the term “usable width” means the width of material that is coated in such a manner
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 7617 2003
链接地址:https://www.31doc.com/p-3779332.html