ISO-9975-1990.pdf
《ISO-9975-1990.pdf》由会员分享,可在线阅读,更多相关《ISO-9975-1990.pdf(12页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 9975 .First edition 1990-12-15 Round non-alloy steel wires for locked coil mine winding ropes - Specifications Fils trCtil - the conditions with which coatings, if any, shall comply: - the conditions of sampling and control. It applies to round, bright or zinc-coated wires
2、 of quality B and of nominal diameters between 1 mm and 3,5 mm. It does not apply to steel wire taken from manufac- tured ropes. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time
3、of publi- cation, the editions indicated were valid. All stan- dards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of ap- plying the most recent editions of the standards in- dicated below. Members of IEC and IS0
4、 maintain registers of currently valid International Standards. IS0 5614:1988, Locked coil wire ropes for mine hoisting - Technical delivery requirements. IS0 6892:1984, Metallic materials - Tensile testing. IS0 7800:1984, Mefallic materials - Wire - Simple torsion test. IS0 7801:1984, Metallic mate
5、rials - Wire - Reverse bend test. IS0 7802:1983, Mefallic materials - Wire - Wrapping test. 3 Wire characteristics 3.1 General conditions of manufacture Wire shall be made by the basic open hearth, elec- tric furnace, or basic oxygen steel process, or by equivalent methods. The finished wires shall
6、not show superficial or internal defects detrimental to their use. When specified, the wires shall be supplied with a zinc coating applied by the hot-dip or the electrolytic process. For the former case, the zinc used shall be 99,9 % pure. 3.2 Diameter 3.2.1 Nominal diameter, d The nominal diameter
7、of the wire, in millimetres, is that by which the wire is designated. It shall be the basis on which the values of all characteristics are determined for acceptance of the wire. 3.2.2 Actual diameter The actual diameter of the wire is the arithmetic mean of two measurements carried out in accord- an
8、ce with 5.1. It shall be within the limits of tolerance specified in table 1. 3.2.3 Ovality of the wire The arithmetic difference between the two measurements of the diameter shall be not more than half the tolerance specified in table 1. Copyright International Organization for Standardization Prov
9、ided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 22:06:22 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 9975:1990(E) Table 1 - Tolerances on diameter Values in millimetres Table 2 - Tolerances on tensile grad
10、e I Nominal diameter of wire Tolerance on diameter d Bright and zinc-coated wires quality B 1 lina . - Samp!es for Delivery unit Production coil Bobbins and spools mechanical tests inspection tests for galvanized coating At one end of each bobbin or spool At one end of every three bobbins or spools
11、5 Tests 5.1 Measurement of diameter The diameter shall be determined from two measurements in two perpendicular directions in the same section and on the same diametrical plane, using a micrometer accurate to 0,Ol mm. 5.2 Tensile test The tensile test shall be carried out in accordance with IS0 6892
12、. The rate of stressing may be greater than that specified in IS0 6692, in view of the num- ber of tests on wire involved in the inspection of the batch. However, it shall not exceed a rate producing an elongation of 25 % of the distance between grips within 1 min. The length of the test piece shall
13、 pref- erably be such that the distance between the grips of the testing machine is 100 mm. In case of dispute, the tensile test shall be per- formed strictly in accordance with IS0 6892, par- ticularly with regard to the rate of stressing. 5.3 Reverse bend test The test shall be carried out in acco
14、rdance with IS0 7801, with the radius of curvature of supports specified in table 3. 5.4 Simple torsion test The test shall be carried out in accordance with IS0 7800, with the number of torsions specified in table 4. A length of 100d for the test piece between grips is preferred. If this length can
15、not be adopted, an alternative length shall be chosen at the wire manufacturer s discretion. In this case, the minimum number of torsions which the wire shall withstand shall be proportional to the number specified in ta- ble4, for a test length of IOOd. Copyright International Organization for Stan
16、dardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 22:06:22 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 9975:1990(E) 5.5 Inspection of zinc coating The determination of mass of zinc shall be c
17、arried out in accordance with annex A. An adhesion test shall be carried out in accordance with annex B. 6 Certificate According to the purchaser s order, one of the fol- lowing control documents may be established. 6.1 Certificate of conformity By this certificate, the manufacturer acknowledges tha
18、t the conditions as specified in the purchaser s order are fulfilled. 6.2 Full works certificate This certificate shall give the results of tests carried out by the manufacturer in accordance with this International Standard. 6.3 Certificate of acceptance In particular cases, when requested by the p
19、ur- chaser, tests may be undertaken after manufacture in the presence of the purchaser or his represen- tative. The test results shall be provided in the cer- tificate of acceptance, which is equivalent to a full works certificate. 7 Marking Each delivery unit shall be marked and identified by a dur
20、able label securely fixed to each coil or bobbin clearly indicating at least the following: 4 b) cl d) 8 the name of the manufacturer or supplier; the indications relative to the wire (diameter, surface condition, tensile grade. and mass or length per delivery unit); - the number of the customer s o
21、rder; the number of the bobbin or coil. Information to be supplied by the purchaser The purchaser shall indicate with the order: a) reference to this International Standard; b) the nominal diameter of the wire; c) the surface finish (bright, zinc-coated quality B); d) the tensile grade of wire; e) t
22、he type of certificate to be supplied by the manufacturer; f) the mass or length of the delivery unit 5 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/23/2007 22:06:22 MDTNo reproductio
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 9975 1990
链接地址:https://www.31doc.com/p-3779604.html