《ISO-93-1-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-93-1-2006.pdf(14页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 93-1:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 93-1 Fourth edition 2006-04-01 Textile machinery and accessories Cylindrical sliver cans Part 1: Main dimensions Matriel pour lindustrie textile Pots cylindriques pour rubans Partie 1: Dimensions principales Copyright Internation
2、al Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) PDF disclaimer This PDF file may contain embedded t
3、ypefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not in
4、fringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were o
5、ptimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified,
6、 no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case po
7、stale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1
8、/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) ISO 2006 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me
9、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme
10、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Dire
11、ctives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bod
12、ies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 93-1 was prepared by Technical Committee ISO/TC 72, Textile machinery and acc
13、essories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories. This fourth edition cancels and replaces the third edition (ISO 93-1:1998), which has been technically revised. ISO 93 consists of the following parts, under the general title Textile machine
14、ry and accessories Cylindrical sliver cans: Part 1: Main dimensions Part 2: Spring bottoms Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networki
15、ng permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- INT
16、ERNATIONAL STANDARD ISO 93-1:2006(E) ISO 2006 All rights reserved 1 Textile machinery and accessories Cylindrical sliver cans Part 1: Main dimensions 1 Scope This part of ISO 93 specifies the main dimensions of cylindrical sliver cans used in the textile industry. 2 Sliver cans without castors 2.1 S
17、ymbols, specifications These shall be as follows: d inside diameter d1 outside diameter at base d1 = d + 15 mm d2 diameter of recess d2 = d 15 mm d5 outside diameter from the top rim of can d5 up to 700 mm: d5 = d + 30 mm, maximum d5 up to 1 200 mm: d5 = d + 40 mm, maximum d5 greater than 1 200 mm:
18、d5 = d + 50 mm, maximum NOTE The stability of the can requires a greater top rim of can for greater diameters of sliver cans. h overall height h1 height of recess See Figures 1 and 2. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Techni
19、cal Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) 2 ISO 2006 All rights reserved Dimensions and tolerances in millimetres Figure 1 Flat base can Copyright International Organization for Standardiz
20、ation Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) ISO 2006 All rights reserved 3 Dimensions and tolerances in millimetres h1 = 5 0
21、20+ Figure 2 Inverted base can Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E)
22、 4 ISO 2006 All rights reserved 2.2 Main dimensions These shall be in accordance with Table 1. Table 1 Dimensions and tolerances of sliver cans without castors Dimensions in millimetres d 3 h 300 350 400 450 500 600 700 900 300 350 400 450 500 600 700 1 000 400 450 500 600 700 1 100 450 500 600 700
23、a 1 200 b a Inside diameters d greater than 700 mm shall be in increments of 100 mm. b Heights h greater than 1 200 mm shall be in increments of 100 mm. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not
24、for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) ISO 2006 All rights reserved 5 3 Sliver cans with castors 3.1 Symbols, specifications These shall be as follows: d inside diameter d1 outside diameter at base d1 = d + 15 mm d2
25、diameter of recess d2 = d 15 mm d5 outside diameter from the top rim of can d5 up to 700 mm: d5 = d + 30 mm, maximum d5 up to 1 200 mm: d5 = d + 40 mm, maximum d5 greater than 1 200 mm: d5 = d + 50 mm, maximum NOTE The stability of the can requires a greater top rim of can for greater diameters of s
26、liver cans. h overall height with castors See Figure 3. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from I
27、HS -,-,- ISO 93-1:2006(E) 6 ISO 2006 All rights reserved Dimensions and tolerances in millimetres This drawing shows a can with three castors, but cans may be fitted with four castors, particularly for inside diameters above 700 mm. See Table 2. Figure 3 Sliver can with castors Copyright Internation
28、al Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) ISO 2006 All rights reserved 7 3.2 Main dimensions
29、These shall be in accordance with Table 2. Table 2 Dimensions and tolerances of sliver cans with castors Dimensions in millimetres d 3 h d3 400 450 500 600 900 280 330 380 480 400 450 500 600 700 800 900 1 000 280 330 380 480 540 640 740 450 500 600 700 800 900 1000 1 100 330 380 480 540 640 740 840
30、 450 500 600 700 800 900 1 000 a 1 200 b 330 380 480 540 640 740 840 a Inside diameters d greater than 1 000 mm shall be in increments of 200 mm. b Heights h greater than of 1 200 mm shall be in increments of 100 mm. Copyright International Organization for Standardization Provided by IHS under lice
31、nse with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) 8 ISO 2006 All rights reserved 4 Designation The designation used for ordering a cylindrical sliver car shall inc
32、lude the following information: a) type (with or without castors); b) reference to this part of ISO 93, i.e. “ISO 93-1”; c) number of castors (R), if applicable; d) inside diameter, d; e) overall height, h; EXAMPLE 1 Sliver can without castors with inside diameter d = 600 mm and overall height h = 1
33、200 mm: Can without castors ISO 93-1 - 600 1200 EXAMPLE 2 Sliver can with three castors with inside diameter d = 600 mm and overall height h = 1200 mm: Can with castors ISO 93-13R - 600 1200 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA
34、 Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resal
35、e, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 93-1:2006(E) ICS 59.120.10 Price based on 8 pages ISO 2006 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 10:49:33 MDTNo reproduction or networking permitted without license from IHS -,-,-
链接地址:https://www.31doc.com/p-3779908.html