ISO-8566-2-1995.pdf
《ISO-8566-2-1995.pdf》由会员分享,可在线阅读,更多相关《ISO-8566-2-1995.pdf(8页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD AtPm Ildx%mat Doe t3ec I IS0 8566-2 First edition 1995-08-01 Cranes - Cabins - Part 2: Mobile cranes Appareils de levage 2 charge suspendue - Cabines - Partie 2: Grues mobiles Reference number IS0 8566-2:1995(E) Copyright International Organization for Standardization Provided
2、 by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 01:03:32 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8586-2:1995(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation o
3、f national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. In
4、ternational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical
5、committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 8566-2 was prepared by Technical Committee lSO/TC 96, Cranes, Subcommittee SC 6, Mobile cranes. IS0 8
6、566 consists of the following parts, under the general title Cranes - Cabins: - Part 1: General - Part 2: Mobile cranes - Part 3: Tower cranes - Part 4: Jib cranes - Part 5: Overhead traveling and portal bridge cranes Annex A of this part of IS0 8566 is for information only. 0 IS0 1995 All rights re
7、served. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case Postale 56
8、l CH-1211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 01:03:32 MDTNo reproduction or networking permitted without license fr
9、om IHS -,-,- INTERNATIONAL STANDARD 0 ISO IS0 8566-2:1995(E) Cranes - Cabins - Part 2: Mobile cranes 1 Scope This part of IS0 8566 establishes the criteria for cabins for mobile cranes as defined in IS0 4306-2. These criteria are intended to cover cabins only for crane operation and not for road tra
10、vel. The general criteria for cabins on mobile cranes are presented in IS0 8566-l. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 8566. At the time of publication, the editions indicated were valid. A
11、ll standards are subject to revision, and parties to agreements based on this part of IS0 8566 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS
12、0 7752-2:1985, Lifting appliances - Controls - Layout and characteristics - Part 2: Basic arrange- ment and requirements for mobile cranes. IS0 8566-1:1992, Cranes - Cabins - Part 1: Gen- eral. IS0 11660-2: 1994, Cranes - Access, guards and re- straints - Part 2: Mobile cranes. 3 General requirement
13、s 3.1 The general requirements for mobile crane cabins may apply to the operation of the crane for lifting and for job-site travel. 3.2 The general requirements for the cabin, includ- ing those concerning visibility, noise and vibration, shall be in accordance with IS0 8566-l. 4 Cabin construction 4
14、.1 Cabins and enclosures shall be constructed to protect the operator s station from the weather. 4.2 Windows shall be provided in the front, top/roof and on both sides of the cabin with visibility forward, upward and to either side consistent with structural requirements. Visibility forward shall i
15、nclude a vertical range adequate to cover the jib point at all times. When a cabin is mounted on the chassis and the boom is capable of slewing in excess of 180” independent of the cabin, the cabin shall be provided with windows on all sides. A windscreen wiper shall be provided on the front window
16、and the top/roof window. The front or top/roof window may have a section which can be readily removed or held open, if desired. If the section is of the type held in the open position, it shall be capable of being secured to prevent inad- vertent closure. Cabin windows shall be equipped with latches
17、 which guard against opening the windows from outside the cabin. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 01:03:32 MDTNo reproduction or networking permitted without lic
18、ense from IHS -,-,- IS0 8566-2:1995(E) 0 IS0 Windows next to the moving jib or hoist mechanisms shall limit the amount of opening or be equipped with guards to restrict egress through the window, includ- ing head and/or arm protrusions through the window, opening or guard. Cabin windows shall be of
19、durable transparency, made of safety-glass or its equivalent which does not lose transparency under exposure to natural light and which resists mechanical shock. 4.3 All cabin doors, whether of the sliding or swinging type, shall be restrained from inadvertent opening or closing during travelling or
20、 operation of the machine. The door adjacent to the driver, if of the swinging type, should open outward and, if of the sliding type, should slide rearward to open. A clear passageway shall be provided from the driver s station to an exit door on the driver s side. Cabin doors shall be equipped with
21、 locks or a locking means to control entrance into the cabin. 4.4 If access to the cabin roof for rigging or service is required, a ladder or steps shall be provided in ac- cordance with IS0 11660-2. 4.5 Provisions shall be made in the cabin for storage of operator s manuals and any other crane info
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 8566 1995
链接地址:https://www.31doc.com/p-3779915.html