《ISO-6162-2-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-6162-2-2002.pdf(26页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 6162-2 First edition 2002-12-01 Reference number ISO 6162-2:2002(E) ISO 2002 Hydraulic fluid power Flange connectors with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 1
2、3 to DN 51 Transmissions hydrauliques Raccordements bride avec demi-brides ou bride monobloc et vis mtriques ou en inches Partie 2: Raccordements bride pour utilisation des pressions de 35 MPa (350 bar) 40 MPa (400 bar), DN 13 DN 51 ISO 6162-2:2002(E) ii ISO 2002 All rights reserved PDF disclaimer T
3、his PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept t
4、herein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file;
5、 the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 All rights re
6、served. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requ
7、ester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ISO 6162-2:2002(E) ISO 2002 All rights reserved iii Contents Page 1Scope . 1 2Normative references . 1 3Terms and definitions 2 4Mat
8、erial . 2 5General specifications 2 6Dimensions . 3 7Tolerances 3 8Finish 3 9Pressure/temperature requirements . 4 10Marking . 4 11Designation of flange connections and their parts . 5 12Identification statement (Reference to this part of ISO 6162) . 5 Annexes AEquivalent SAE O-rings 16 BEquivalent
9、inch screw strengths 17 Bibliography. 18 ISO 6162-2:2002(E) iv ISO 2002 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried
10、out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
11、collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committee
12、s are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 6162 may be the subject of patent rights. ISO shall n
13、ot be held responsible for identifying any or all such patent rights. International Standard ISO 6162-2 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components. This first edition of ISO 6162-2 together with first edition
14、 of ISO 6162-1 cancel and replace the first edition of ISO 6162:1994, which has been technically revised. ISO 6162 consists of the following parts, under the general title Hydraulic fluid power Flange connectors with split or one-piece flange clamps and metric or inch screws: Part 1: Flange connecto
15、rs for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51 Annexes A and B of this part of ISO 6162 are for information only. ISO 6162-2:2002(E) ISO 2002 All rights reserved v
16、 Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Components are interconnected through their ports and associated fluid conductor connector ends. INTERNATIONAL STANDARDISO 6162-2:2002(E) ISO 2002 All right
17、s reserved 1 Hydraulic fluid power Flange connectors with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51 WARNING Users of this part of ISO 6162 shall ensure that suitable material is ch
18、osen for the port to maintain the required working pressure, if carbon steel is not used. Also, the tube material and wall thickness depend on the selected working pressure and tube diameter. Tube dimensions shall be calculated in accordance with ISO 10763. 1Scope This part of ISO 6162 specifies com
19、plete general and dimensional characteristics for flange heads, split flange clamps (FCS), one-piece flange clamps (FC) and ports applicable to four-screw, split and one-piece flange clamp type tube and hose connectors for use at pressures of ( 1) to (). It also specifies the dimensions of the seals
20、 to be used, as well as the grooves to house the seal. This part of ISO 6162 also recognizes the need to accommodate metric (type 1) screw fasteners, as well as to provide a means to use existing inch (type 2) screw fasteners. These connectors are intended for application in hydraulic systems on ind
21、ustrial and commercial products, where it is desired to avoid the use of threaded connectors. Surges of pressure higher than the nominal ratings will reduce the ability of the flange connectors to retain the hydraulic fluid. This should be taken into account in the design of the hydraulic system. 2N
22、ormative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 6162. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements base
23、d on this part of ISO 6162 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently v
24、alid International Standards. ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) ISO 261, ISO general-purpose metric screw threads General plan ISO 263, ISO inch screw threads General plan and selection for screws, bolts and nuts Diameter ra
25、nge 0.06 to 6 in ISO 273, Fasteners Clearance holes for bolts and screws 1); . 35 MPa 350 bar40 MPa 400 bar 1 bar=0,1 MPa=105Pa 1 Pa=1 N/m2 ISO 6162-2:2002(E) 2 ISO 2002 All rights reserved ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 898-1, Mechanical properties of fastene
26、rs made of carbon steel and alloy steel Part 1: Bolts, screws and studs ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 3601-1, Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and size i
27、dentification code ISO 3601-3, Fluid power systems O-rings Part 3: Quality acceptance criteria ISO 5598, Fluid power systems and components Vocabulary ISO 8434-5, Metallic tube connections for fluid power and general use Part 5: Test methods for threaded hydraulic fluid power connections ISO 9227, C
28、orrosion tests in artificial atmospheres Salt spray tests ISO 10763, Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures ASME/B1.1, Unified Inch Screw Threads (UN and UNR Thread Form) 3Terms and definitions For the purposes of this part
29、 of ISO 6162, the terms and definitions given in ISO 5598 apply. 4Material 4.1 Split flange clamp halves (see Figure 3) and one-piece flange clamps (see Figure 4) shall be made from ferrous material with the following properties: minimum yield strength: ; minimum elongation at fracture: . 4.2 Use fl
30、ange heads made from ferrous material with: minimum yield strength: ; minimum elongation at fracture: . 4.3 Use hex head metric screws of property class 8.8 or 10.9, as specified in ISO 898-1, or equivalent inch screws (see annex B). 4.4 Unless otherwise specified, the O-rings shall be made of NBR (
31、nitrile) with a hardness of () IRHD, measured in accordance with ISO 48, for use at the pressure and temperature requirements given in clause 9 and in Table 1 or in Table 2, and for testing. The O-rings shall conform to the dimensions given in Table 4 and shall meet or exceed the O-ring quality acce
32、ptance criteria for grade N of ISO 3601-3. NOTEFor higher temperatures, use sealing materials that meet the higher requirements. 5General specifications 5.1 Select from Tables 1 or 2 and Table 3 either type 1 (metric) or type 2 (inch), split (FCS) or one-piece (FC) flange clamps and ports, depending
33、 on whether metric or inch screw fasteners are required. 331 N/mm2 3 % 215 N/mm2 10 % 905 ISO 6162-2:2002(E) ISO 2002 All rights reserved 3 5.2 Use hexagon head screws, unless otherwise specified. Table 1 lists pressures and torques when property class 8.8 (in accordance with ISO 898-1) screws are c
34、hosen. These screws should be used for severe vibration applications, e.g. for rigid piping. Table 2 lists pressures and torques when property class 10.9 (in accordance with ISO 898-1) screws are chosen. In this case, the surface pressure on the screw head and between flange clamp and flange head sh
35、all be considered. Hardened flat washers may be used. 5.3 If socket head cap screws are necessary and screws of property classes 8.8 or 10.9 are not available, use screws of property class 12.9 in accordance with ISO 898-1 (see annex B for equivalent inch screws). 6Dimensions The following specifica
36、tions supplement the dimensional data contained in Tables 1 to 4 with respect to all unspecified details. a)Select the nominal matching flange size clamp for the matching port size from Figures 3 to 5 and Table 3. b)Select the size for flange heads, shown in Figure 6 and Table 4, in accordance with
37、the size selected for the flange clamps and ports. NOTEThe flange head selection is not affected by the difference in metric or inch screw fasteners. c)Use O-ring seals (see Figure 7) that conform to the dimensions in ISO 3601-1, which are repeated in Table 4 of this part of ISO 6162. For equivalent
38、 SAE O-rings, see annex A. d)Select metric or inch screws corresponding to the sizes and lengths indicated in Tables 1 or 2 and, depending upon whether type 1 or type 2 flange clamps were chosen, as specified in 5.1 and 5.2. e)Designate both thread size and length of screws. f)Designate four-screw s
39、plit-flange or one-piece flange connector sizes by the nominal flange diameter that corresponds to the maximum diameter of the bore through the flanged head. 7Tolerances All dimensions for flange clamps and flange heads which are not otherwise limited shall be in accordance with ISO 273, medium seri
40、es, and ISO 2768-1, class m. NOTEDimensions and tolerances given in the tables apply to the finished parts, plated or otherwise processed, as specified by the purchaser. 8Finish 8.1 The external surface on all flanges, except weld-on flange heads, shall be protected with an appropriate coating to pa
41、ss a minimum salt spray test in accordance with ISO 9227, unless otherwise agreed upon by the supplier and purchaser. Weld-on flange heads shall be protected from corrosion by an oil film, phosphate coating or by other means that do not negatively affect weldability to meet a neutral salt spray test
42、 in accordance with ISO 9227, unless otherwise agreed upon by the supplier and purchaser. 8.2 Flange clamps shall meet the requirements of a salt spray test in accordance with ISO 9227, unless otherwise agreed upon by the supplier and purchaser. 8.3 Screws and washers shall meet the requirements of
43、a salt spray test in accordance with ISO 9227. All screws of property class 10.9 shall be phosphate coated with an oil finish. 72-h 16-h 32-h 16-h ISO 6162-2:2002(E) 4 ISO 2002 All rights reserved 8.4 Any appearance of red rust during the above salt spray tests shall be considered failure, except fo
44、r the following: all internal passages; edges such as hex points, serrations and crests of threads where there may be mechanical deformation of the plating or coating typical of mass-produced parts or shipping effects; areas where there is mechanical deformation of the plating or coating caused by c
45、rimping, flaring, bending and other post-plate metal forming operations; areas where the parts are suspended or affixed in the test chamber and condensate can accumulate. 8.5 All connection components shall be free from hanging burrs, loose scale and slivers that might become dislodged in use, and f
46、rom all other defects that might affect their serviceability. All machined surfaces shall have a surface roughness value of , except where otherwise specified. 8.6 A smooth sealing surface shall be provided. Annular tool marks up to a surface roughness value, , of shall be permitted. 8.7For more spe
47、cific finish requirements, see Figures 1 to 6. 9Pressure/temperature requirements 9.1 Testing shall be conducted in accordance with ISO 8434-5 to determine that flange connectors conforming to this part of ISO 6162 meet the specified pressure/temperature requirements. Burst and cyclic endurance test
48、s shall be conducted on flange connections. 9.2 Flange connectors complying with this part of ISO 6162 and made of carbon steel shall be suitable for use at the working pressures given in Tables 1 and 2 when used at fluid temperatures between and . Such connectors shall be suitable for use in hydrau
49、lic systems at ambient temperatures from to . NOTEThe temperature range of connectors with elastomeric seals depends on the limits of the temperature range of the seal. 9.3 Flange connectors complying with this part of ISO 6162 and made of stainless steel shall be suitable for use at the working pressures given in Tables 1 and 2 when used at temperatures between and . Working pressure for connectors made from stainless steel and used at elevated temperatures shall be red
链接地址:https://www.31doc.com/p-3780035.html