ISO-9185-2007.pdf
《ISO-9185-2007.pdf》由会员分享,可在线阅读,更多相关《ISO-9185-2007.pdf(20页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 9185:2007(E) ISO 2007 INTERNATIONAL STANDARD ISO 9185 Second edition 2007-07-01 Protective clothing Assessment of resistance of materials to molten metal splash Vtements de protection valuation de la rsistance des matriaux aux projections de mtal fondu Copyright International O
2、rganization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=DAWSON, DAVIS Not for Resale, 07/03/2007 02:02:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9185:2007(E) PDF disclaimer This PDF file may contain embedde
3、d typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not
4、 infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters wer
5、e optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reser
6、ved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the request
7、er. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Lic
8、ensee=IHS Employees/1111111001, User=DAWSON, DAVIS Not for Resale, 07/03/2007 02:02:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9185:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms an
9、d definitions. 1 4 Principle. 1 5 Apparatus and materials 2 6 Conditioning 6 7 Preparation of test specimens 6 8 Operator safety . 6 9 Procedure 7 9.1 Setting up the apparatus 7 9.2 Preparation of molten metal or cryolite 7 9.3 Attachment of test material to pin frame 7 9.4 Pouring 7 9.5 Examination
10、. 7 9.6 Determination of mass of metal poured. 8 10 Iterative testing . 8 11 Void tests. 8 12 Test report . 8 Annex A (normative) Test conditions for certain metals and for cryolite 9 Annex B (normative) Method of test for assessment of thermal characteristics of PVC sensor film. 11 Bibliography. 12
11、 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=DAWSON, DAVIS Not for Resale, 07/03/2007 02:02:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9185:2007(E) iv ISO 2007 All rights
12、 reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for
13、 which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on a
14、ll matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are
15、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held re
16、sponsible for identifying any or all such patent rights. ISO 9185 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in collaboration with Technical Committee ISO/TC 94, Personal safe
17、ty Protective clothing and equipment, Subcommittee SC 13, Protective clothing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This second edition cancels and replaces the first edition (ISO 9185:1990), which has been technically revised. This second
18、 edition includes the following significant technical changes compared to the first edition: a) new PVC sensor film included; b) Cryolite included as test metal. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=DA
19、WSON, DAVIS Not for Resale, 07/03/2007 02:02:58 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9185:2007(E) ISO 2007 All rights reserved v Introduction ISO 9185:1990 and EN 373:1995 have been used up until now with reasonable success as the principle test methods for m
20、aterials used in the manufacture of clothing to protect against large splashes of molten metals. EN and ISO specifications cite these test methods and set levels of performance in terms of the mass of iron or aluminium that can be splashed onto test materials without producing damage to the heat sen
21、sor film. The revision of the test methods contained within this International Standard incorporates changes based on experience that are intended to improve reproducibility and to respond to incident data from the aluminium smelter industry. A test procedure is therefore introduced to determine the
22、 protection provided by materials when splashed with molten cryolite. This revision also harmonises into one test procedure the previously slightly different procedures in ISO 9185 and EN 373 for testing with molten aluminium. A new supply of PVC sensor film has been established together with a new
23、world-wide distributor see note in the text. One single specification for PVC film replaces the previously different ones in ISO 9185 and EN 373. The test method in this International Standard is distinct from that in ISO 9150, which assesses the protective performance of materials intended to be ma
24、nufactured into protective clothing for welding activities. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=DAWSON, DAVIS Not for Resale, 07/03/2007 02:02:58 MDTNo reproduction or networking permitted without lic
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 9185 2007
链接地址:https://www.31doc.com/p-3780459.html