ISO-9211-4-2006.pdf
《ISO-9211-4-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-9211-4-2006.pdf(18页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 9211-4:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 9211-4 Second edition 2006-05-01 Optics and optical instruments Optical coatings Part 4: Specific test methods Optique et instruments doptique Traitements optiques Partie 4: Mthodes dessai spcifiques ISO 9211-4:2006(E) PDF disc
2、laimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties
3、accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to t
4、he file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All r
5、ights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of
6、the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved ISO 9211-4:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv 1 Scope .
7、1 2 Normative references. 1 3 Terms and definitions. 1 4 Test conditioning 1 5 Abrasion resistance tests (conditioning method 01: abrasion) 1 5.1 General. 1 5.2 Test conditions . 2 5.3 Degree of severity (conditioning method 01: abrasion). 2 5.4 Recovery 2 5.5 Evaluation 2 6 Adhesion tests (conditio
8、ning method 02: adhesion) 3 6.1 General. 3 6.2 Test conditions . 3 6.3 Degree of severity (conditioning method 02: adhesion) 3 6.4 Recovery 3 6.5 Evaluation 3 7 Crosshatch test (conditioning method 03: crosshatch). 4 7.1 General. 4 7.2 Test conditions . 4 7.3 Conditioning 4 7.4 Recovery 4 7.5 Evalua
9、tion 4 8 Solubility tests (conditioning method 04: solubility) 5 8.1 General. 5 8.2 Test conditions . 5 8.3 Degree of severity (conditioning method 04: solubility) 5 8.4 Recovery 6 8.5 Evaluation 6 9 Environmental test code 6 Annex A (normative) Materials for abrasion testing of optical coatings 7 A
10、nnex B (normative) Cheesecloth pad, pad cover and fixture preparation for moderate abrasion testing of optical coatings . 10 Annex C (informative) Visual examination of optical coatings 12 Bibliography. 13 ISO 9211-4:2006(E) iv ISO 2006 All rights reserved Foreword ISO (the International Organizatio
11、n for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has
12、 the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Inter
13、national Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publicat
14、ion as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent righ
15、ts. ISO 9211-4 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 3, Optical materials and components. This second edition cancels and replaces the first edition (ISO 9211-4:1996), Clauses 4, 5, 6, and Table 3 and Annex A of which have been technically revised. A n
16、ew Clause 6 and Table 3 have been added to this second edition. The original Clause 6 has been renumbered Clause 7 and the original Table 3 has been renumbered Table 4. A new normative Annex B has been added and the previous Annex B is now Annex C. ISO 9211 consists of the following parts, under the
17、 general title Optics and optical instruments Optical coatings: Part 1: Definitions Part 2: Optical properties Part 3: Environmental durability Part 4: Specific test methods INTERNATIONAL STANDARD ISO 9211-4:2006(E) ISO 2006 All rights reserved 1 Optics and optical instruments Optical coatings Part
18、4: Specific test methods 1 Scope This part of ISO 9211 describes surface treatments of components and substrates excluding ophthalmic optics (spectacles) by the application of optical coatings, and gives a standard form for their specification. It defines the general characteristics and the test and
19、 measurement methods whenever necessary, but is not intended to define the process method. This part of ISO 9211 describes specific test procedures for coating environmental durability tests that are identified in ISO 9211-3 but not described in other normative references. 2 Normative references The
20、 following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 48, Rubber, vulcanized or thermoplastic Determin
21、ation of hardness (hardness between 10 IRHD and 100 IRHD). 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 9211-1:1994 apply. 4 Test conditioning Before and after subjecting a coated specimen (component or witness sample) to any inspection or test, t
22、he specimen shall be thoroughly cleaned as required to remove dirt, finger marks, smears, etc. Recommended storage time is at least 12 h after the coating process under ambient atmospheric conditions, or as specified between manufacturer and buyer. 5 Abrasion resistance tests (conditioning method 01
23、: abrasion) 5.1 General The purpose of these tests is to evaluate to what extent the optical and mechanical properties of optical coatings on components and substrates are affected when subjected to specific abrading conditions at ambient atmospheric conditions. ISO 9211-4:2006(E) 2 ISO 2006 All rig
24、hts reserved 5.2 Test conditions 5.2.1 General Abrasion tests shall be conducted using a coating abrasion tester capable of meeting the requirements of 5.2 and 5.3. The length of stroke of the tester shall be approximately 20 mm when the dimensions of the specimen permit. A stroke is defined as one
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 9211 2006
链接地址:https://www.31doc.com/p-3780482.html