ISO-4190-2-2001.pdf
《ISO-4190-2-2001.pdf》由会员分享,可在线阅读,更多相关《ISO-4190-2-2001.pdf(24页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 4190-2 Second edition 2001-02-01 Reference number ISO 4190-2:2001(E) ISO 2001 Lift (US: Elevator) installation Part 2: Class IV lifts Installation dascenseurs Partie 2: Ascenseurs de classe IV Copyright International Organization for Standardization Provided by IHS under l
2、icense with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 00:13:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 4190-2:2001(E) ii ISO 2001 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance w
3、ith Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing
4、 policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Ev
5、ery care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publicat
6、ion may be reproduced or utilized in any form or by any means, elec- tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs mem- ber body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Gene
7、va 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 00:13:40 MDTNo rep
8、roduction or networking permitted without license from IHS -,-,- ISO 4190-2:2001(E) ISO 2001 All rights reserved iii ContentsPage 1Scope .1 2Normative references .1 3Terms and definitions 1 4Lift characteristics .4 4.1Renard series 4 4.2Rated loads .4 4.3Rated speeds 5 4.4Lift selection .5 5Dimensio
9、ns .5 5.1Inner dimensions of cars .5 5.2Inner dimensions of well (US: hoistway) 5 5.3Dimensions of landings .6 5.4Dimensions of machine room 6 5.5Arrangement of machine room 6 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Stan
10、dards 1/9972545001 Not for Resale, 04/19/2007 00:13:40 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 4190-2:2001(E) iv ISO 2001 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
11、 (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical com- mittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations
12、, governmental and non-governmental, in liai- son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the
13、ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that so
14、me of the elements of this part of ISO 4190 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 4190-2 was prepared by Technical Committee ISO/TC 178,Lifts, escalators, passenger conveyors. This second editi
15、on cancels and replaces the first edition (ISO 4190-2:1982), which has been technically revised. It reflects the requirements of the global marketplace. A range of goods (freight) lifts typically used for rated speeds of 0,25 m/s to 2,5 m/s and loads of 630 kg to 5 000 kg has been incorporated. The
16、dimensions on the car are related to the loads which have been based on the R10 series of numbers but, due to the predominance of hydraulic drives, some have been based on other considerations. The range of loads has been extended up to 5 000 kg and includes both the car and landing entrance configu
17、ration. Two classes of loading related to car floor area have been adressed to reflect different safety code requirements. Additional loads incurred whilst loading/unloading the car are not part of the rated load. ISO 4190 consists of the following parts, under the general titleLift (US: Elevator) i
18、nstallation: Part 1: Class I, II, III and VI lifts Part 2: Class IV lifts Part 3: Service lifts class V Part 5: Control devices, signals and additional fittings Part 6: Passenger lifts to be installed in residential buildings Planning and selection Copyright International Organization for Standardiz
19、ation Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 00:13:40 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 4190-2:2001(E) ISO 2001 All rights reserved 1 Lift (US: Elevator) instal
20、lation Part 2: Class IV lifts 1Scope This part of ISO 4190 specifies the necessary dimensions to permit the installation of Class IV lifts, as defined in 3.2.4, generally used for the transport of goods (freight). It deals with electric and hydraulic lifts. The horizontal dimensions of the wells (US
21、: hoistways) are generally defined by the entrance and drive configurations. It covers lifts with either horizontal or vertical power-operated sliding doors see Figures 1 a) and 1 b). For other characteristics, the manufacturers should be consulted. This part of ISO 4190 is applicable to new lift in
22、stallations, with a car with one or two entrances, to be installed in a new building. Where relevant, it may be used as a basis for an installation in an existing building. Two types of loading (load per unit area) are addressed: Series A: passenger and goods (freight) lifts with loading conforming
23、to EN 81-1 or EN 81-2; Series B: lifts for goods (freight) only, which have a different floor loading in countries which allow this by virtue of their safety codes. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions
24、 of this part of ISO 4190. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 4190 are encouraged to investigate the possi- bility of applying the most recent editions of the normative docu
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 4190 2001
链接地址:https://www.31doc.com/p-3780767.html