ISO-5183-2-2000.pdf
《ISO-5183-2-2000.pdf》由会员分享,可在线阅读,更多相关《ISO-5183-2-2000.pdf(10页珍藏版)》请在三一文库上搜索。
1、Reference number ISO 5183-2:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 5183-2 Second edition 2000-12-01 Resistance spot welding Electrode adaptors, male taper 1:10 Part 2: Parallel shank fixing for end-thrust electrodes quipement de soudage par rsistance Allonges dlectrode embout amovible, cne mle
2、1:10 Partie 2: Emmanchement cylindrique pour pousse en bout Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:54:02 MDTNo reproduction or networking permitted without license fr
3、om IHS -,-,- ISO 5183-2:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the edi
4、ting. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be
5、 found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at
6、 the address given below. ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address belo
7、w or ISOs member body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reserved Copyright International Organization for Standardi
8、zation Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:54:02 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 5183-2:2000(E) ISO 2000 All rights reservediii Foreword ISO (the International Organization f
9、or Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has th
10、e right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internat
11、ional Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the membe
12、r bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 5183 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 5183-2 was prepared by Technical Committe
13、e ISO/TC 44, Welding and allied processes, Subcommittee SC 6, Resistance welding. This second edition cancels and replaces the first edition (ISO 5183-2:1988), which has been technically revised. ISO 5183 consists of the following parts, under the general title Resistance spot welding Electrode adap
14、tors, male taper 1:10: ?Part 1: Conical fixing, taper 1:10 ?Part 2: Parallel shank fixing for end thrust electrodes Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:54:02 MDTNo
15、 reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:54:02 MDTNo reproduction or networking permitted without l
16、icense from IHS -,-,- INTERNATIONAL STANDARDISO 5183-2:2000(E) ISO 2000 All rights reserved1 Resistance spot welding Electrode adaptors, male taper 1:10 Part 2: Parallel shank fixing for end-thrust electrodes 1Scope This part of ISO 5183 specifies the dimensions and tolerances of resistance spot wel
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 5183 2000
链接地址:https://www.31doc.com/p-3781250.html