《ISO-8640-3-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-8640-3-2002.pdf(40页珍藏版)》请在三一文库上搜索。
1、 Reference number Numro de rfrence ISO 8640-3:2002(E/F) ISO 2002 INTERNATIONAL STANDARD NORME INTERNATIONALE ISO 8640-3 First edition Premire dition 2002-07-01 Textile machinery and accessories Flat warp knitting machines Part 3: Vocabulary of patterning devices Matriel pour lindustrie textile Machi
2、nes tricoter rectilignes mailles jetes Partie 3: Vocabulaire des dispositifs dessin Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/11/2007 20:22:56 MDTNo reproduction or networking perm
3、itted without license from IHS -,-,- ISO 8640-3:2002(E/F) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the c
4、omputer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to c
5、reate this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform
6、the Central Secretariat at the address given below. PDF Exonration de responsabilit Le prsent fichier PDF peut contenir des polices de caractres intgres. Conformment aux conditions de licence dAdobe, ce fichier peut tre imprim ou visualis, mais ne doit pas tre modifi moins que lordinateur employ cet
7、 effet ne bnficie dune licence autorisant lutilisation de ces polices et que celles-ci y soient installes. Lors du tlchargement de ce fichier, les parties concernes acceptent de fait la responsabilit de ne pas enfreindre les conditions de licence dAdobe. Le Secrtariat central de lISO dcline toute re
8、sponsabilit en la matire. Adobe est une marque dpose dAdobe Systems Incorporated. Les dtails relatifs aux produits logiciels utiliss pour la cration du prsent fichier PDF sont disponibles dans la rubrique General Info du fichier; les paramtres de cration PDF ont t optimiss pour limpression. Toutes l
9、es mesures ont t prises pour garantir lexploitation de ce fichier par les comits membres de lISO. Dans le cas peu probable o surviendrait un problme dutilisation, veuillez en informer le Secrtariat central ladresse donne ci-dessous. ISO 2002 The reproduction of the terms and definitions contained in
10、 this International Standard is permitted in teaching manuals, instruction booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are: that no modifications are made to the terms and definitions; that such reproduction
11、is not permitted for dictionaries or similar publications offered for sale; and that this International Standard is referenced as the source document. With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means, electronic or mech
12、anical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. La reproduction des termes et des dfinitions contenus dans la prsente Norme internationale est autorise dans les manuels denseignement
13、, les modes demploi, les publications et revues techniques destins exclusivement lenseignement ou la mise en application. Les conditions dune telle reproduction sont les suivantes: aucune modification nest apporte aux termes et dfinitions; la reproduction nest pas autorise dans des dictionnaires ou
14、publications similaires destins la vente; la prsente Norme internationale est cite comme document source. la seule exception mentionne ci-dessus, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris
15、 la photocopie et les microfilms, sans laccord crit de lISO ladresse ci-aprs ou du comit membre de lISO dans le pays du demandeur. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland/Imprim e
16、n Suisse ii ISO 2002 All rights reserved/Tous droits rservs Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/11/2007 20:22:56 MDTNo reproduction or networking permitted without license fr
17、om IHS -,-,- ISO 8640-3:2002(E/F) ISO 2002 All rights reserved/Tous droits rservs iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out th
18、rough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collab
19、orates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Stan
20、dards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of
21、 this part of ISO 8640 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8640-3 was prepared by Technical Committee ISO/TC 72, Textile machinery and machinery or dry-cleaning and industrial laundering, Subcommittee SC 3, Machine
22、ry for fabric manufacturing including preparatory machinery and accessories. ISO 8640 consists of the following parts, under the general title Textile machinery and accessories Flat warp knitting machines: Part 1: Driving mechanisms, supports and knitting elements Part 2: Warp let-off, fabric take-u
23、p and batching Part 3: Vocabulary of patterning devices Part 4: Stitch bonding machines and stitch bonding devices Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/11/2007 20:22:56 MDTNo
24、reproduction or networking permitted without license from IHS -,-,- ISO 8640-3:2002(E/F) iv ISO 2002 All rights reserved/Tous droits rservs Avant-propos LISO (Organisation internationale de normalisation) est une fdration mondiale dorganismes nationaux de normalisation (comits membres de lISO). Llab
25、oration des Normes internationales est en gnral confie aux comits techniques de lISO. Chaque comit membre intress par une tude a le droit de faire partie du comit technique cr cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en liaison avec lISO, participent ga
26、lement aux travaux. LISO collabore troitement avec la Commission lectrotechnique internationale (CEI) en ce qui concerne la normalisation lectrotechnique. Les Normes internationales sont rdiges conformment aux rgles donnes dans les Directives ISO/CEI, Partie 3. La tche principale des comits techniqu
27、es est dlaborer les Normes internationales. Les projets de Normes internationales adopts par les comits techniques sont soumis aux comits membres pour vote. Leur publication comme Normes internationales requiert lapprobation de 75 % au moins des comits membres votants. Lattention est appele sur le f
28、ait que certains des lments de la prsente partie de lISO 8640 peuvent faire lobjet de droits de proprit intellectuelle ou de droits analogues. LISO ne saurait tre tenue pour responsable de ne pas avoir identifi de tels droits de proprit et averti de leur existence. LISO 8640-3 a t labore par le comi
29、t technique ISO/TC 72, Matriel pour lindustrie textile et machines pour le nettoyage sec et la blanchisserie industrielle, sous-comit SC 3, Matriel pour la fabrication dtoffe y compris le matriel de prparation, et accessoires. LISO 8640 comprend les parties suivantes, prsentes sous le titre gnral Ma
30、triel pour lindustrie textile Machines tricoter rectilignes mailles jetes: Partie 1: Pices dentranement, supports et lments de tricotage Partie 2: Droulement de la chane, enroulement et chargement du tricot Partie 3: Vocabulaire des dispositifs dessin Partie 4: Machines et dispositifs de couture-tri
31、cotage Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/11/2007 20:22:56 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD NORME INTERNATION
32、ALE ISO 8640-3:2002(E/F) ISO 2002 All rights reserved/Tous droits rservs 1 Textile machinery and accessories Flat warp knitting machines Part 3: Vocabulary of patterning devices Matriel pour lindustrie textile Machines tricoter rectilignes mailles jetes Partie 3: Vocabulaire des dispositifs dessin 1
33、 Scope This part of ISO 8640 defines terms related to the following types of patterning device used on flat warp knitting machines: lapping devices for warp ends; patterning presser devices; fall plate patterning devices; yarn let-off and yarn tensioning patterning devices; needle bar stopping devic
34、es; weft insertion devices; take-up patterning devices. NOTE 1 The figures in this part of ISO 8640 illustrate the working principles of the various aggregates. They do not represent the only, or even the most common, arrangements. In any case, to the extent technically possible, these devices are a
35、ble to be combined. NOTE 2 In addition to terms and definitions used in two of the three official ISO languages (English and French), this part of ISO 8640 gives the equivalent terms and definitions in the German language; these are published under the responsibility of the member body for Germany (
36、DIN). However, only the terms and definitions given in the official languages can be considered as ISO terms and definitions. 1 Domaine dapplication La prsente partie de lISO 8640 dfinit les termes lis aux dispositifs dessin suivants utiliss sur les machines tricoter rectilignes mailles jetes: dispo
37、sitif de jete des fils de chane; dispositif dessin avec presse; dispositif dessin avec plaque de rabattage; dispositif dessin avec tendeurs et appel de fils; dispositif darrt de la barre aiguilles; dispositif dinsertion trame; dispositif dessin par lappel de fils. NOTE 1 Les figures dans la prsente
38、partie de lISO 8640 montrent le principe de fonctionnement des divers lments. Elles ne reprsentent pas le seul type dexcution possible ni mme le plus frquent. En tout cas, ces dispositifs peuvent tre combins, dans la mesure des possibilits techniques. NOTE 2 En complment des termes et dfinitions uti
39、liss dans deux des trois langues officielles de lISO (anglais et franais), la prsente partie de lISO 8640 donne les termes et dfinitions quivalents dans la langue allemande; ces termes et dfinitions sont publis sous la responsabilit du Comit membre de lAllemagne (DIN). Toutefois, seuls les termes et
40、 dfinitions donns dans les langues officielles peuvent tre considrs comme tant des termes et dfinitions de lISO. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/11/2007 20:22:56 MDTNo re
41、production or networking permitted without license from IHS -,-,- ISO 8640-3:2002(E/F) 2 ISO 2002 All rights reserved/Tous droits rservs 2 Terms and definitions 2 Termes et dfinitions 2 Begriffe und Definitionen No. No Nr. Term Terme Begriff Definition Dfinition Definition 2.1 lapping device for war
42、p ends patterning device for the lateral displacement of the yarn guides dispositif de jete des fils de chane dispositif dessin pour le dplacement latral des passettes Lege-Einrichtung fr Kettfden Mustereinrichtung zum seitlichen Versatz fr Fadenleger 2.1.1 pattern drive (for guide bar control) devi
43、ce which, according to the design, controls the lateral displacement of the guide bars in the underlaps and overlaps mcanisme dessin commandant les barres passettes dispositif qui, en fonction du dessin, commande le dplacement latral des barres passettes en jete sous et sur Mustergetriebe zur Steuer
44、ung der Legebarren Einrichtung, die den seitlichen Versatz der Legebarren in der Unter- und berlegung mustergem steuert 2.1.1.1 one-shaft pattern drive pattern drive in which the control of the lateral displacement of the guide bars is determined by a single shaft via pattern disks or pattern drums
45、with chain links to the guide bars mcanisme dessin un seul arbre mcanisme dans lequel la commande de dplacement latral des barres passettes est dtermine par un arbre unique au moyen de disques ou de tambours dessin maillons Mustergetriebe mit nur einer Welle Getriebe in welchem die Steuerung des sei
46、tlichen Versatzes der Legebarren durch eine Einzelwelle bestimmt wird, mittels Musterscheiben oder Mustertrommeln mit Kettengliedern Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/11/20
47、07 20:22:56 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 8640-3:2002(E/F) ISO 2002 All rights reserved/Tous droits rservs 3 No. No Nr. Term Terme Begriff Definition Dfinition Definition 2.1.1.1.1 direct controlled one-shaft pattern drive one-shaft pattern drive giving direct control of the lateral displacement of the guide bars See Figure 1. mcanisme dessin un seul arbre commande directe mcanisme dessin un seul arbre assurant la commande directe du dp
链接地址:https://www.31doc.com/p-3781256.html