ISO-TR-17165-2-2006.pdf
《ISO-TR-17165-2-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-TR-17165-2-2006.pdf(28页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO/TR 17165-2:2006(E) ISO 2006 TECHNICAL REPORT ISO/TR 17165-2 First edition 2006-09-15 Hydraulic fluid power Hose assemblies Part 2: Recommended practices for hydraulic hose assemblies Transmissions hydrauliques Flexibles de raccordement Partie 2: Pratiques recommandes pour les f
2、lexibles de raccordement hydrauliques Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Hong Kong Polytechnic Univ/9976803100 Not for Resale, 04/17/2007 09:57:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 17
3、165-2:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloadi
4、ng this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the Gene
5、ral Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given
6、 below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member b
7、ody in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved Copyright International Organization for Standardization Provided
8、by IHS under license with ISO Licensee=Hong Kong Polytechnic Univ/9976803100 Not for Resale, 04/17/2007 09:57:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 17165-2:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 No
9、rmative references. 1 3 Terms and definitions. 2 4 Safety considerations. 2 5 Hose selection and routing 4 6 Hose assembly fabrication 11 7 Hose installation and replacement . 12 8 Maintenance inspection. 14 9 Hose storage . 16 10 Identification statement (reference to this part of ISO 17165). 17 An
10、nex A (informative) Examples of actual failure resulting from improper use . 18 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Hong Kong Polytechnic Univ/9976803100 Not for Resale, 04/17/2007 09:57:34 MDTNo reproduction or networking permitte
11、d without license from IHS -,-,- ISO/TR 17165-2:2006(E) iv ISO 2006 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out
12、through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO coll
13、aborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International St
14、andards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In exceptional circumstances, when a technical committee has col
15、lected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example), it may decide by a simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely informative in nature and does not
16、have to be reviewed until the data it provides are considered to be no longer valid or useful. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TR
17、 17165-2 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components. ISO/TR 17165 consists of the following parts, under the general title Hydraulic fluid power Hose assemblies: Part 1: Dimensions and requirements Part 2: Re
18、commended practices for hydraulic hose assemblies (Technical Report) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Hong Kong Polytechnic Univ/9976803100 Not for Resale, 04/17/2007 09:57:34 MDTNo reproduction or networking permitted without l
19、icense from IHS -,-,- ISO/TR 17165-2:2006(E) ISO 2006 All rights reserved v Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. To allow fluid flow between components, they are interconnected by piping, both r
20、igid (tubes and tube connectors) and flexible (hose assemblies, which consist of hose and hose fittings). Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Hong Kong Polytechnic Univ/9976803100 Not for Resale, 04/17/2007 09:57:34 MDTNo reproduct
21、ion or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Hong Kong Polytechnic Univ/9976803100 Not for Resale, 04/17/2007 09:57:34 MDTNo reproduction or networking permitted without license fro
22、m IHS -,-,- TECHNICAL REPORT ISO/TR 17165-2:2006(E) ISO 2006 All rights reserved 1 Hydraulic fluid power Hose assemblies Part 2: Recommended practices for hydraulic hose assemblies 1 Scope This part of ISO 17165 provides guidelines for selection, routing, fabrication, installation, replacement, main
23、tenance and storage of hose and hose assemblies for hydraulic fluid power systems, which are manufactured from hoses conforming to ISO 1436-1, ISO 1436-2, ISO 3862-1, ISO 3862-2, ISO 3949, ISO 4079-1, ISO 4079-2, ISO 11237-1 and ISO 112372, and hose connectors conforming to ISO 12151-1 through ISO 1
24、2151-6. NOTE 1 Many of these recommended practices can also be suitable for use with other types of hoses and systems. NOTE 2 Annex A (informative) lists examples of actual failure resulting from improper use of hydraulic hose and hose assemblies. 2 Normative references The following referenced docu
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO TR 17165 2006
链接地址:https://www.31doc.com/p-3781393.html