ISO-7682-2003.pdf
《ISO-7682-2003.pdf》由会员分享,可在线阅读,更多相关《ISO-7682-2003.pdf(38页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 7682:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 7682 Second edition 2003-11-15 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Acrylonitrile-butadiene-styrene (ABS) Systmes de canalisations en plastique pour lvacuation des eaux-
2、 vannes et des eaux uses ( basse et haute temprature) lintrieur des btiments Acrylonitrile-butadine-styrne (ABS) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Qatar Petroleum/5943408001 Not for Resale, 04/12/2007 00:43:17 MDTNo reproduction
3、or networking permitted without license from IHS -,-,- ISO 7682:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and inst
4、alled on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software prod
5、ucts used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found,
6、please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in wri
7、ting from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved Copyrigh
8、t International Organization for Standardization Provided by IHS under license with ISO Licensee=Qatar Petroleum/5943408001 Not for Resale, 04/12/2007 00:43:17 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7682:2003(E) ISO 2003 All rights reserved iii Contents Page Fo
9、rewordiv Introduction v 1 Scope1 2 Normative references .1 3 Symbols and abbreviations .2 4 Material.3 5 General characteristics 4 6 Geometrical characteristics.4 7 Mechanical characteristics of pipes .21 8 Physical characteristics.23 9 Performance requirements 24 10 Sealing rings25 11 Adhesives 25
10、12 Marking.25 13 Installation of piping systems .26 Annex A (informative) Additional characteristics of ABS pipes and fittings .28 Bibliography .29 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Qatar Petroleum/5943408001 Not for Resale, 04/1
11、2/2007 00:43:17 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7682:2003(E) iv ISO 2003 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepari
12、ng International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in lia
13、ison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of
14、technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is
15、drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7682 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of
16、fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). This second edition cancels and replaces the first edition (ISO 7682:1991), which has been technically revised. Copyright International Organization for Standardization Provided by IHS unde
17、r license with ISO Licensee=Qatar Petroleum/5943408001 Not for Resale, 04/12/2007 00:43:17 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 7682:2003(E) ISO 2003 All rights reserved v Introduction Pipes and fittings conforming to this International Standard also meet the
18、 corresponding requirements of EN 1455-1 which are applicable to those pipes and fittings which, according to EN 1455-1, are intended to be used inside buildings (application area code “B”, see EN 1455-1) only. Copyright International Organization for Standardization Provided by IHS under license wi
19、th ISO Licensee=Qatar Petroleum/5943408001 Not for Resale, 04/12/2007 00:43:17 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Qatar Petroleum/5943408001 Not for Resale,
20、 04/12/2007 00:43:17 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 7682:2003(E) ISO 2003 All rights reserved 1 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Acrylonitrile-butadiene- styrene (ABS
21、) 1 Scope This International Standard specifies the requirements for solid-wall acrylonitrile-butadiene-styrene (ABS) pipes and fittings for soil and waste discharge (low and high temperature) above ground inside buildings, as well as the system itself. It does not include buried pipework. It also s
22、pecifies the test parameters for the test methods referred to in this International Standard. This International Standard is applicable to ABS pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes: a) soil and waste discharge pipework fo
23、r the conveyance of domestic waste waters (low and high temperature); b) ventilation pipework associated with a); c) rainwater pipework inside the building. It is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose
24、sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints. Two systems, system I and system II, are specified for type N ring seal sockets. Both systems are suitable for this field of application.1) 2 Normative references The following referenced documents are indispensable for
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 7682 2003
链接地址:https://www.31doc.com/p-3781549.html