JIS-B-1005-2003-ENG.pdf
《JIS-B-1005-2003-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-1005-2003-ENG.pdf(6页珍藏版)》请在三一文库上搜索。
1、J IS JAPANESE INDUSTRIAL STA N DA R D Translated and Published by Japanese Standards Association (IS0 885 2000) (JFRI/ JSA) General purpose bolts and screws- Metric series-Radii under the head ICs 21.060.10 Reference number : JIS B 1005 : 2003 (E) PROTECTED BY COPYRIGHT 4s Copyright Japanese Standar
2、ds Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:19:20 MSTNo reproduction or networking permitted without license from IHS -,-,- B 1005 : 2003 (IS0 885 : 2000) Foreword This translation has been made based on the
3、original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Research Institute for Screw Threads and Fa
4、steners (JFRI)/ the Japanese Standards Association (JSA) with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standard- ization Law applicable to the case of revision by the provision of Article 14. Consequently JIS E 1005 : 1985 is replaced with this Standa
5、rd. This revision has been prepared to conform to IS0 885 : 2000 General purpose bolts and screws-Metric series-Radii under the head. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility
6、 model right or application for registration of utility model after opening to the public which have technical properties. The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public,
7、 utility model right or application for registration of utility model after opening to the public which have the said technical properties. Date of Establishment: 1985-11-01 Date of Revision: 2003-03-20 Date of Public Notice in Official Gazette: 2003-03-20 Investigated by: Japanese Industrial Standa
8、rds Committee Standards Board Technical Committee on Machine Elements JIS B 1005 : 2003, First English edition published in 2003-08 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the
9、 original JIS is to be the final authority. O JSA 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publis
10、her. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:19:20 MSTNo reproduction or networking permitted without license from IHS -,-,- B 1005 : 2003
11、 (IS0 885 : 2000) Contents Page Introduction . 1 1 Scope 1 2 Dimensions . 1 (i PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:19:20 MSTNo reproduction or networki
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 1005 2003 ENG
链接地址:https://www.31doc.com/p-3782218.html