《ISO-6965-1982.pdf》由会员分享,可在线阅读,更多相关《ISO-6965-1982.pdf(8页珍藏版)》请在三一文库上搜索。
1、International Standard INTERNATIONAL ORGANIZATION FOR STANDARDIZATlON.MEYHAPOHAR OPrAHHJAUHR n0 CTAHjWWl3Al - or to lift a 6 058 mm (20 ft) pallet or other non-corner fitting equipped ULD, through adequate attachment devices; - or to lift various pieces of outsize cargo. 3.4 The system of slings or
2、chains system shall be designed to avoid any interference between the slings or chains and the container structures. The devices engaging and lifting the con- tainer shall be designed to avoid any damage to cast aluminium corner fittings. 3.5 The gantry and spreader design, as well as the length and
3、 design of the slings or chains, when used between the spreader and the load, shall allow stacking 2 438 mm (96 in) high con- tainers on two levels. 3.6 For maintenance purposes or in order to allow inter- change of various spreaders, it shall be possible to deposit the spreader or to pick it up, on
4、, or from the ground. 3.7 A variety of (additional) sling attachment points may be provided on the spreader, as specified by the buyer, to allow safe slinging and lifting of various pieces of outsize cargo to be handled. 3.8 Provisions for using common lifting hardware shall be made to that effect.
5、An adjustable lifting speed, preferably in the range of 193 m/min (6 ft/min) to 550 m/min (18 ft/min) under the maximum load of 27 200 kg (60 000 lb) shall be provided. 3.9 The lifting speed shall be the same when hoisting or lowering. It shall be possible to raise each end of the container or outsi
6、ze load independently. 3.10 Lateral spreader movement shall be provided over a total range not less than 610 mm (24 in). The lateral movement speed shall be adjustable from 0 to at least 0,61 m/min (0 to 2 ft/min). Lateral movement of fore and aft ends of spreader shall be independently and/or simul
7、taneously controlled. 3.11 Statutory safety regulations relating to mobile lifting equipment shall be applied. 4 Mobility and stability 4.1 Ground stabilizers or stabilizing devices shall not be necessary for the operation of the unit. 4.2 In order to provide adequate stability, the unit s wheel bas
8、e shall equal or exceed 6 058 mm (20 ft). 4.3 The unit shall be capable of being driven with the max- imum load of 27 200 kg (60 000 lb) at speeds up to 10 km/h (6 mph) for at least 3 km (2 miles). The unit shall effectively and safely control the maximum load up to the maximum driv- ing speed. 4.4
9、Power steering shall be provided. 4.5 The unloaded unit shall be able to start moving on a 5O slope. 4.6 The swept turn radius, measured at the outermost part, shall be kept to a minimum and shall not exceed 9,15 m (30 ft), not including the spreader, if designed for 12 192 mm (490 in) container cap
10、acity. 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 00:32:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6965-1982 (E) 4.7 The unloaded uni
11、t in the raised position shall be safe in wind velocities up to 193 km/h (120 mph). 4.8 The wheel footprint shall be such that pressure on the ground does not exceed 14 bar (170 Ib/sq. in) when the unit is loaded with the maximum load of 27 200 kg (60 000 lb). 5.2 In addition, an electrical remote c
12、ontrol box, of minimum weight and size, of the type most currently used on lifting gan- tries, may be provided on the side of the unit opposite to the driver s position, for lifting functions only. 5.3 Ample lighting is required for night operations and to il- luminate the load and close surrounding
13、s. 5 Controls 5.1 All controls necessary to move and operate the unit shall be located in the driver s position. 5.4 Normal power system warning and indicator lights shall be provided. 3 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Tec
14、hnical Standards 1/9972545001 Not for Resale, 04/27/2007 00:32:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6965-1962 (E) Spreader .- E z Y- a : E E Lf Lf 3 660mm(12ftlmin. 5 180mm(l7ft)max. Figure 1 - Explanation of specification clearances 7 /f/ 4 Copyright Inte
15、rnational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 00:32:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6965-1982 (El Self-centring gather devices (Shown here in
16、 raised position) - -Remotely controlled top lifting twistlock Figure 2 - Remotely controlled spreader I 533mm (60.375in) A I 533mm J (60.375 in) 6 058mm (238.5in) w -iE .- 0 2 -is E 9 N i E-z Es gq2 Figure 3 - Nominal location of the eight lifting sling/chain attachment points 5 Copyright Internati
17、onal Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 00:32:08 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 00:32:08 MDTNo reproduction or networking permitted without license from IHS -,-,-
链接地址:https://www.31doc.com/p-3782255.html