ISO-9136-2-1999.pdf
《ISO-9136-2-1999.pdf》由会员分享,可在线阅读,更多相关《ISO-9136-2-1999.pdf(10页珍藏版)》请在三一文库上搜索。
1、A Reference number ISO 9136-2:1999(E) INTERNATIONAL STANDARD ISO 9136-2 First edition 1999-10-15 Abrasive grains Determination of bulk density Part 2: Microgrits Grains abrasifs Dtermination de la masse volumique apparente Partie 2: Micrograins Copyright International Organization for Standardizatio
2、n Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 22:19:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9136-2:1999(E) ISO 1999 All rights reserved. Unless otherwise specified, no part of this publicati
3、on may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 CH-1211 Genve 20 Switzerland Internetisoiso.ch Printed in Swi
4、tzerland ii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject f
5、or which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on
6、 all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internationa
7、l Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 9136-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. ISO 9136 consists of the following parts, under the general title Abrasiv
8、e grains Determination of bulk density: Part 1: Macrogrits Currently ISO 9136:1989 Part 2: Microgrits Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 22:19:18 MDTNo reproduction
9、or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISOISO 9136-2:1999(E) 1 Abrasive grains Determination of bulk density Part 2: Microgrits 1 Scope This part of ISO 9136 specifies a test method for the determination of the bulk density of bonded and coated abrasive microgr
10、its. 2 Term and definition For the purposes of this part of ISO 9136, the following term and definition apply. 2.1 bulk density rB this, of a pourable abrasive grain which is poured in a certain way, is the quotient of the mass and the volume, specified in g/cm3 3 Testing equipment The testing equip
11、ment is shown in Figure 1. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 22:19:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9136-2:1999(E) I
12、SO 2 Key 1 Overspill tray 2 Measuring cylinder 3 Shield 4 Stand 5 Funnel 6 Vibration channel 7 Vibration generator 8 Rubber feet Metering device Figure 1 Equipment for the determination of bulk density of microgrits 3.1 Metering Device The metering device1) is isolated by rubber feet, so that vibrat
13、ions are not transmitted to the surroundings. The most important components are: a) vibration generator; b) stainless steel funnel with a polished inner surface and the following main dimensions: 1) total height of funnel: 290 mm; 1) Metering device type DR1000/40 can be obtained from Fa. F. Kurt Re
14、tsch GmbH 3) inside diameter of cylindrical outlet: 28 mm; 4) height of cylindrical outlet: 38 mm; c) stainless steel horizontal vibration channel, with the following dimensions (210 mm 3 40 mm 3 30 mm) 1 mm (length 3 width 3 depth). The distance from the lower edge of the funnel to the bottom of th
15、e vibration channel must be (8 4) mm; d) stand. 3.2 Measuring cylinder The measuring cylinder has a polished inner surface and a volume V of (200 0,5) cm3; this volume is achieved by an inner diameter of 64 mm and an inner height of 62,2 mm. The measuring cylinder is placed centrally under the strea
16、m coming from the vibration channel. The height of fall of the microgrit to be tested (from the upper edge of the channel bottom to the bottom of the measuring cylinder) shall be (140 1) mm. Calibration of the measuring cylinder can be achieved by the following two methods. Method A The dry, empty m
17、easuring cylinder is weighed together with a flat glass plate. The measuring cylinder is filled with water and the glass plate placed on the cylinder in such a way that no air bubble is present. The glass plate is held in this position, the surplus water removed and the total weight determined. The
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 9136 1999
链接地址:https://www.31doc.com/p-3782330.html