ISO-9173-1-2006.pdf
《ISO-9173-1-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-9173-1-2006.pdf(12页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 9173-1:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 9173-1 Second edition 2006-06-01 Dentistry Extraction forceps Part 1: General requirements and test methods Art dentaire Daviers Partie 1: Exigences gnrales et mthodes dessai Copyright International Organization for Standardiza
2、tion Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9173-1:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing
3、policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Cent
4、ral Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been tak
5、en to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
6、 or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01
7、 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:16:10 MDTNo reproduct
8、ion or networking permitted without license from IHS -,-,- ISO 9173-1:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 Requirements 2 4.1 Materials 2 4.2 Maximum overall length. 2 4.3 Rockwell hardnes
9、s . 2 4.4 Surface finish 2 4.5 Resistance to autoclaving . 2 4.6 Resistance to corrosion and thermal exposure 3 4.7 Joint opening/closing force. 3 5 Test methods. 3 5.1 Visual inspection 3 5.2 Resistance test 3 5.3 Joint opening/closing force. 4 6 Marking 4 Copyright International Organization for S
10、tandardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9173-1:2006(E) iv ISO 2006 All rights reserved Foreword ISO (the International Organization for Standa
11、rdization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right t
12、o be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Sta
13、ndards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an In
14、ternational Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9173
15、-1 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental instruments. This second edition cancels and replaces the first edition (ISO 9173-1:1991), which has been technically revised. The following changes have been made: a) the scope has been expanded to cover all ext
16、raction forceps; b) the descriptions of the test procedures have been improved; c) the requirements for specific forceps have been removed and will be included in a future part of ISO 9173. ISO 9173 consists of the following parts, under the general title Dentistry Extraction forceps: Part 1: Genera
17、l requirements and test methods Further parts are planned. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9
18、173-1:2006(E) ISO 2006 All rights reserved v Introduction This revision of ISO 9173-1 is intended to cover all extraction forceps used in dentistry. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/200
19、7 02:16:10 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 02:16:10 MDTNo reproduction or networking permitted without li
20、cense from IHS -,-,- INTERNATIONAL STANDARD ISO 9173-1:2006(E) ISO 2006 All rights reserved 1 Dentistry Extraction forceps Part 1: General requirements and test methods 1 Scope This part of ISO 9173 specifies the general performance requirements for extraction forceps used in dentistry. 2 Normative
21、references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1942, Dentistry Vocabulary ISO 650
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 9173 2006
链接地址:https://www.31doc.com/p-3782375.html