JIS-B-0601-2001-R2005-ENG.pdf
《JIS-B-0601-2001-R2005-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-0601-2001-R2005-ENG.pdf(29页珍藏版)》请在三一文库上搜索。
1、J IS JAPANESE I N DUSTR IAL STANDARD Translated and Published by Japanese Standards Association a 4 Geometrical Product Specif i cat ions (G PS)- a Surface texture I Profile method- Terms, definitions and surface texture parameters ICs 01.040.17; 17.040.20 Descriptors : roughness (surface), smoothne
2、ss (surface), surface treatment, vocabulary Reference number : JIS B 0601 : 2001 (E) 15 S B 0601 : 2001 (IS0 4287 : 1997) Foreword This translation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Jap
3、anese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by the Japanese Standards Association (JSA) with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law. Consequently JIS B 06
4、01 : 1994 is revised, and JIS B 0660 : 1998 Surface roughness-Terminology-Part 1 : Surface and its parameters is withdrawn and integrated into this Standard. In this Standard “Ten-point mean roughness” which is used in Japan up to now, and “Center line average roughness” according to the former Stan
5、dard are described in Annex 1 and Annex 2, respectively for information. Date of Establishment: 1952-05-21 Date of Revision: 2001-01-20 Date of Public Notice in Official Gazette: 2001-01-22 Investigated by: Japanese Industrial Standards Committee Divisional Council on Machine Elements TIS B 0601 :20
6、01, First English edition published in 2001-11 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. b O JSA 2001 All rights reserved. Unless
7、otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan JAPANESE INDUSTRIAL STANDARD JIS B 0601 : 2001 (IS0 4287 : 19
8、97) Geometrical Product Specifications (GPS)- Surface texture : Profile method- Terms, definitions and surface texture parameters Introduction This Japanese Industrial Standard has been prepared based on IS0 4287 Geometrical Product Specifications (GPS)-Surface texture: Profile method- Terms, defini
9、tions and surface texture parameters issued in 1997 without modifying the technical contents. This Standard is a Geometrical Product Specification (GPS) standard and is to be regarded as a General GPS standard (see TR B 0007). It influences chain link 2 of the chains of standards on surface texture.
10、 For more detailed information on the relationship of this Standard to other standards and the GPS matrix model, see Annex D. Historically, the roughness profile and its parameters have been the only parts of surface texture characterization that have been well defined. A default relationship betwee
11、n Ac and A f is under consideration. In this Standard, ten-point mean roughness which is used in Japan even at present and center line average roughness which had been specified in the former standard are described in Annex 1 and Annex 2, respectively for information. The portions with solid sidelin
12、es or dotted underlines show the matters not in- cluded in the original International Standard. NOTE : TR B 0007 is identical with ISOPTR 14638 : 1995 Geometrical Product Specification (GPS)-Masterplan. 1 Scope This Standard specifies terms, definitions and parameters for the deter- mination of surf
13、ace texture (roughness, waviness and primary profile) by profiling methods. NOTE : The International Standard corresponding to this Standard is as follows. In addition, abbreviations which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT
14、 (identical), MOD (modified) and NEQ (not equivalent) accord- ing to ISOAEC Guide 21. IS0 4287 : 1997 Geometrical Product Specifications (GPS)-Surface texture : Profile method-Terms, definitions and surface texture parameters (IDT) 2 Normative references The following standards contain provisions wh
15、ich, through reference in this Standard, constitute provisions of this Standard. The most recent editions of the standards (including amendments) indicated below shall be applied. JIS B 0632 Geometrical Product Specification (GPS)-Surface texture : Profile method-Metrological characteristics of phas
16、e correct filters -,-,- 2 B 0601 : 2001 (IS0 4287 : 1997) NOTE : IS0 11562 : 1996 Geometrical Product Specifications (GPS)-Surface texture : Profile method-Metrological characteristics of phase correct filters is identical with the said standard. JIS B 0633 Geometri.ca1 Product Specifications (GPS)-
17、Surface texture : Profile method-Rules and procedures for the assessment of surface texture NOTE : IS0 4288 : 1996 Geometrical Product Specifications (GPS)-Surface texture: Profile method-Rules and procedures for the assessment of surface texture is identical with the said standard. JIS B 0651 Surfa
18、ce texture-Instruments for the assessment of surface texture- Profile method NOTE : IS0 3274 : 1996 Geometrical Product Specifications (GPS)-Surface texture : Profile method-Nominal characteristics of contact (stylus) in- struments is identical with the said standard. 3 Definitions The definitions o
19、f terms used in this Standard are as follows. 3.1 General terms 3.1.1 profile filter filter which separates profiles into longwave and shortwave components NOTE : There are three filters used in instruments for measuring roughness, waviness Eind primary profiles (see Figure 1). They all have the sam
20、e transmission characteristics, defined in JIS B 0632, but different cut- off wave-lengths. 3.1.1.1 As profile filter filter which defines the intersection between the roughness and the even shorter wave components present in a surface (see Figure 1) 3.1.1.2 Ac profile filter filter which defines th
21、e intersection between the roughness and waviness components (see Figure 1) 3.1.1.3 A f profile filter filter which defines the intersection between the waviness and the even longer wave components present in a surface (see Figure 1) 3.1.2 coordinate system that coordinate system in which surface te
22、xture parameters are defined NOTE : It is usual to use a rectangular coordinate system in which the axes form a right-handed Cartesian set, the X-axis being the direction of tracing colinear with the mean line, the Y-axis also nominally lying on the real surface, and the Z-axis being in an outward d
23、irection (from the material to the surrounding medium). This convention is adopted throughout the rest of this Standard. b L. b , 4 . -,-,- 3 B 0601 : 2001 (IS0 4287 : 1997) 3.1.3 real surface O surface limiting the body and separating it from the surrounding medium 3.1.4 surface profile profile tha
24、t results from the intersection of the real surface by a specified plane (see Figure 2) NOTE : In practice, it is usual to choose a plane with a normal that nomi- nally lies parallel to the real surface and in a suitable direction. 3.1.5 primary profile See JIS B 0651. Total profile after applicatio
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 0601 2001 R2005 ENG
链接地址:https://www.31doc.com/p-3782416.html