JIS-A-8610-2004-ENG.pdf
《JIS-A-8610-2004-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-A-8610-2004-ENG.pdf(33页珍藏版)》请在三一文库上搜索。
1、J IS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association Building construction machinery and equipment-Internal vibrators for concrete ICs 91.220 Reference number : JIS A 8610 : 2004 (E) PROTECTED BY COPYRIGHT 17 S Copyright Japanese Standards Association Provided
2、 by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 21:21:43 MDTNo reproduction or networking permitted without license from IHS -,-,- A 8610 : 2004 Foreword This translation has been made based on the original Japanese Industrial Standard re
3、vised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by Japan Construction Mechanization Association (JCMA)/Japanese Standards Association (JSA) with
4、 the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14. Consequently JIS A 8610 : 1993 is replaced with this Standard. This revision has been made based on ISO/CD 18651 : 2002 Bu
5、ilding construction machinery and equipment-Internal vibrators for concrete for the purposes of making it easier to compare this Standard with International Standard; to prepare Japanese Industrial Standard conforming with International Standard; and to propose a draft of an International Standard w
6、hich is based on Japanese Industrial Standard. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the publ
7、ic which have technical properties. The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to
8、the public which have the said technical properties. Date of Establishment: 1961-03-01 Date of Revision: 2004-03-20 Date of Public Notice in Official Gazette: 2004-03-22 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Industrial Machinery JIS A 8610 :
9、2004, First English edition published in 2005-01 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIC is to be the final authority. O JSA 2005 All rights reserved. No part
10、 of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under lic
11、ense with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 21:21:43 MDTNo reproduction or networking permitted without license from IHS -,-,- A 8610 : 2004 Contents Page Introduction . 1 2 3 4 5 5.1 5.2 5.3 6 6.1 6.2 6.3 6.4 6.5 6.6 7 7.1 7.2 7.3 7.4 8 9 10 11 Scope
12、 Normative references Terms and definitions . Classification Structure. dimensions and rating time . Structure . Dimensions Rating time . Performance requirements . Frequency Double amplitude (full amplitude) . Evaluation of centrifugal force No-load amplitude . Electric insulation . Daily vibration
13、 exposure Performance testing No load test Load test under water Electrical insulation Daily vibration exposure of flexible shaft . Inspection Designation . Type-plate . Commercial specifications 11.1 11.2 Basic data for all type vibrators . Complementary data for particular vibrator types . 1 1 1 2
14、 4 4 4 4 4 4 4 5 5 6 6 6 6 6 6 7 7 7 7 7 8 8 8 PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 21:21:43 MDTNo reproduction or networking permitted without license fro
15、m IHS -,-,- A 8610 : 2004 12 Instruction handbook 10 Annex A (informative) Examples of structures and dimensional characteristics of internal vibrators . 11 Annex 1 (informative) Comparison table between JIS and corresponding International Standard . 20 (ii) PROTECTED BY COPYRIGHT Copyright Japanese
16、 Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 21:21:43 MDTNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS A 8610 : 2004 Building construction machine
17、ry and equipment-Internal vibrators for concrete Introduction This Japanese Industrial Standard has been prepared based on ISO/ CD 18651 : 2002 Building construction machinery and equipment-Internal vibra- tors for concrete with some modifications of the technical contents. Portions underlined with
18、dots are the matters modified from the original Inter- national Standard. A list of modifications with the explanations is given in annex 1 (informative). 1 This Standard specifies internal vibrators for concrete (hereafter referred to as “vibrators?) used for concrete mix compaction. It is applicab
19、le to only the power driven vibrators with head diameter of 180 mm or less. The International Standard corresponding to this Standard is as follows. In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical),
20、 MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21. ISOICD 18651 : 2002 Building construction machinery and equipment- Internal vibrators for concrete (MOD) Scope NOTE : 2 Normative references The following standards contain provisions which, through reference in this Standard,
21、constitute provisions of this Standard. If the indication of the year of publication is given to these referred standards, only the edition of the indicated year constitutes the provision of this Standard but the revision and amend- ment made thereafter do not apply. The normative references without
22、 the indica- tion of the year of coming into effect apply only to the most recent edition (including amendments). JIS C 4034-1 Rotating electrical machines Part 1 : Rating and performance NOTE : IEC 60034-1 : 1996 Rotating electrical machine-Part 1 :Rating and per- formance is equivalent to the said
23、 standard. JIS C 9745-1 Safety of hand-held motor-operated electric tools-Part 1 : General requirements NOTE : IEC 60745-1 : 1993 Safety of hand-held motor-operated electric tools- Part 1 : General requirements is equivalent to the said standard. JIS C 9745-2-12 Safety of hand-held motor-operated el
24、ectric tools-Part 2-12 :Par- ticular requirements for concrete vibrators (internal vibrators) IEC 60745-2-12 : 1993 Safety of hand-held motor-operated electric tools- Part 2 : Particular requirements for concrete vibrators (internal vibrators) is equivalent to the said standard. NOTE : IS0 8041 : 19
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 8610 2004 ENG
链接地址:https://www.31doc.com/p-3782524.html