JIS-B-1189-2005-ENG.pdf
《JIS-B-1189-2005-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-1189-2005-ENG.pdf(30页珍藏版)》请在三一文库上搜索。
1、J IS JAPANESE I N DU STR I AL STANDARD Translated and Published by Japanese Standards Association Hexagon flange bolts ICs 21.060.10 Reference number : JIS B 1189 : 2005 (E) PROTECTED BY COPYRIGHT 16 S B 1189 : 2005 Foreword This translation has been made based on the original Japanese Industrial St
2、andard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Research Institute for Screw Threads and Fasteners (JFRI)/ Japanese Standa
3、rds Association (JSA) with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standard- ization Law applicable to the case of revision by the provision of Article 14. Consequently JIS B 1189 : 1999 is replaced with this Standard. In order to conform to the Inte
4、rnational Standard, this revision has been prepared based on IS0 15071 : 1999 Hexagon bolts with flange-Small series-Product grade A and IS0 15072 : 1999 Hexagon bolts with flange with metric fine pitch thread-Small series-Product grade A. Attention is drawn to the possibility that some parts of thi
5、s Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties. The relevant Minister and the Japanese Industrial Standards Committee a
6、re not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical properties. Date of Establishment: 1977-10-01 Date of Revision: 20
7、05-03-20 Date of Public Notice in Official Gazette: 2005-03-20 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Machine Elements JIS B 1189 : 2005, First English edition published in 2005-04 Translated and published by: Japanese Standards Association 4-
8、1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JE is to be the final authority. O JSA 2005 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includ
9、ing photocopying and microfilm, without permission in writing from the publisher. Printed in Japan KWAT PROTECTED BY COPYRIGHT -,-,- B 1189 : 2005 Contents Page Introduction . 1 Scope 2 Normative references 3 Classification 4 Shape and dimensions. product specification and designation of products .
10、5 Marking . Annex A (normative) Gauging of hexagon flange heads . Annex 1 (normative) Hexagon flange bolts not based on IS0 15071 and IS0 15072 Annex 2 (informative) Comparison table between JIS and corresponding International Standards . 1 1 1 3 3 4 13 15 23 PROTECTED BY COPYRIGHT JAPANESE INDUSTRI
11、AL STANDARD JIS B 1189 : 2005 Hexagon flange bolts Introduction This Japanese Industrial Standard has been prepared based on IS0 15071 Hexagon bolts with flange-Small series-Product grade A and IS0 15072 Hexa- gon bolts with flange with metric fine pitch thread-Small series-Product grade A published
12、 in 1999 as the first edition by editing and integrating the corresponding parts (shape and dimensions, product specification, and designation of products) without modifying the technical content, while some items not specified in the corresponding International Standards are added as the Japanese I
13、ndustrial Standard. Portions given sidelines or dotted underlines are the matters not stated in the original International Standards. A list of modification with the explanations is given in annex 2 (informative). 1 Scope This Standard specifies the characteristics of hexagon bolts with flange (here
14、after referred to as “bolts”). If, in special cases, specifications other than those listed in this Standard are required, they should be selected from existing standards, for example JIS B 0205-2, JIS B 0209-2, JIS B 1009, JIS B 1051 and JIS B 1054-1. NOTES 1 Flanges based on IS0 15071 and IS0 1507
15、2 are specified in the text, and bolts not based on those are specified in annex 1. 2 The International Standards corresponding to this Standard are as follows. In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT
16、(identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21. IS0 15071 ; 1999 Hexagon bolts with flange-Small series-Product gradeA (MOD) IS0 15072 : 1999 Hexagon bolts with flange with metric fine pitch thread-Small series-Product grade A (MOD) 2 Normative references The fol
17、lowing standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. The most recent editions of the standards (including amendments) indicated below shall be applied. JIS B 0101 Screw threads and fasteners-Vocabulary NOTE : IS0 1891 : 1979 Bolts, sc
18、rews, nuts and accessories-Terminology and nomenclature and IS0 5408 : 1983 Cylindrical screws threads-Vocabu- . “ lary are equivalent to the said standard. JIS B 0143 NOTE : Symbols and designations of dimensions for threaded fasteners IS0 225 : 1983 Fasteners-Bolts, screws, studs and nuts-Symbols
19、and designations of dimensions is equivalent to the said standard. JIS B 0205-2 IS0 general purpose metric screw threads-Part 2 : General plan PROTECTED BY COPYRIGHT -,-,- 2 B 1189 : 2005 NOTE : IS0 261 : 1998 IS0 general-purpose metric screw threads-General plan is identical with the said standard.
20、 JIS B 0209-2 IS0 general purpose metric screw threads-Tolerances-Part 2 : Lim- its of sizes for general purpose external and internal screw threads- Medium quality NOTE : IS0 965-2 : 1998 IS0 general purpose metric screw threads-Toler- ances-Part 2 : Limits of sizes for general purpose external and
21、 inter- nal screw threads-Medium quality is identical with the said standard. Geometrical Product Specification (GPS)-Surface texture : Profile method-Terms, definitions and surface texture parameters JIS B 0601 . NOTE : IS0 4287 : 1997 Geometrical Product Specifications (GPSI-Surface texture . : Pr
22、ofile method-Terms, definitions and surface texture param- eters is identical with the said standard. . . JIS B 1003 NOTE : Fasteners-Ends of parts with external IS0 metric thread IS0 4753 : 1999 Fasteners-Ends of parts with external IS0 metric thread is identical with the said standard. JIS B 1009
23、Bolts, screws and studs-Nominal lengths, and thread lengths for general purpose bolts IS0 888 : 1976 Bolts, screws and studs-Nominal lengths, and thread lengths for general purpose bolts is equivalent to the said standard. NOTE : JIS B 1010 Designation system for fasteners NOTE : IS0 8991 : 1986 Des
24、ignation system for fasteners is identical with the said standard. Tolerances for fasteners-Part 1 : Bolts, screws, studs and nuts- Product grades A, B and C NOTE : IS0 4759-1 : 2000 Tolerances for fasteners-Part 1 :Bolts, screws, studs and nuts-Product grades A, B and C is identical with the said s
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 1189 2005 ENG
链接地址:https://www.31doc.com/p-3782569.html