JIS-B-6510-1989-R2004-ENG.pdf
《JIS-B-6510-1989-R2004-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-6510-1989-R2004-ENG.pdf(14页珍藏版)》请在三一文库上搜索。
1、J I S B*65LO 49 4933608 0016462 4 rp JIS UDC 674.05:621.912.001.4 JAPANESE INDUSTRIAL STANDARD Test Methods for Performance and Accuracy of Spindle Moulding Machines JIS B 6510-1989 Translated and Published by Japanese Standards Association Printed in Japan 8s Copyright Japanese Standards Associatio
2、n Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 03:45:21 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*b5LO 89 4933608 00Lb863 b W In the event of any doubt arising, the original Standard in J
3、apanese is to be final authority. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 03:45:21 MDTNo reproduction or networking permitted without license from IHS -,-,- UDC 674.05: 621.912.001.
4、4 JAPANESE INDUSTRIAL STANDARD J I S Test Methods for Performance and Accuracy B 6510-1989 of Spindle Moulding Machines i. Scope This Japanese Industrial Standard specifies the test methods related to the functions, running performances and rigidity and inspection methods on static accuracies and ma
5、chining accuracies of the spindle moulding machines of 100 mm or under in effective cutting height for the spindle shaper moulding machines, and of 100 mm or under in effective cutting height and 100 mm or over to 680 mm or under in the distance between the main spindle centres for the double-spindl
6、e moulding machines, among the spindle shaper moulding machines specified in No. 6321 and the double spindle moulding machines specified in No, 6322 of JIS B 0114, hereinafter these are generically referred to as the “spindle moulding machines“. Remark: The units and numerical values given in ( ) in
7、 this Standard are based on the traditional unit and are appended for informa- tive reference. 2. Methods for Functional Tests The functional tests on the spindle moulding machines shall be in ac- cordance with Table 1. Applicable Standards : JIS B 0114-Glossary of Terms for Wood Working Machinery J
8、IS B 6507-General Code of Safety for Wood Working Machinery JIS B 6521-Methods of Measurement for Noise Emitted by Wood Working JIS B 6602-Safety Standards for Construction of Spindle Shapers Machinery Corresponding International Standard: IS0 7 O0 9-W oodworking machines- Single spindle moulding ma
9、chines- N omen- clature and acceptance conditions Reference Standards: JIS B 6501-Test Code for Performance and Accuracy of Wood Working JIS Z 8203-SI Units and the Use of their Multiples and of Certain Other Machinery Units Copyright Japanese Standards Association Provided by IHS under license with
10、 JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 03:45:21 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*b5LO 89 W 4933b08 00LbBb5 T 2 B 6510-1989 Table 1. Functional Tests No, 1 - - 2 3 4 5 - 6 7 8 9 Test item Electrical equip me
11、nt Start, stop and running operations of main spindle Changing operation of main spindle speed of rotation Manual feed operation Ascending and descend- ing and clamping operations of main spindle, and operation of automatic stopping device Ascending and descend- ing and clamping operations of table
12、Attaching and detaching of cutter Safety device Lubricating device Test met hod Before and after the running test, examine the insulating condition once each. At an appropriate main spindle speed of rotation, carry out 10 times of start and stop continuously to examine the smoothness and reliability
13、 of actions. Change the main spindle speed of rotation over entire marked speeds of rotation to examine the smoothness of actions and the reliability of indications of the operating device. Examine the smoothness and uniformity of actions throughout overall length of movement by the manual feed hand
14、le, and rotate the sensitive feed handle several times to examine the smoothness and uniformity. Allow the main spindle to ascend and descend to examine the smoothness and uniformity of actions throughout overall length of the motions, and examine the reliability of clamping and the smoothness of ac
15、tions of the clamping device at the both ends and centre of motions. In addition, examine the smoothness and reliability of actions of the automatic stopping device at the both ends of motions. Ascend and descend the table to examine the smoothness and uniformity of actions throughout the overall le
16、ngth of motions. In addition, examine the reliability of clamping and the smoothness of actions of the clamping device at the both ends and centre of motions. Examine the reliability and smoothness of the attaching, detaching and clamping screw of the cutter. Examine the reliability of the safety fu
17、nctions for operators and protective functions for machine see JIS B 6507 and JIS B 66021. Examine the reliability of such functions as oil tightness and proper distribution of quantity of oil. a Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/11
18、11111001, User=Wing, Bernie Not for Resale, 03/14/2007 03:45:21 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*bSLO 89 = 4933608 OOLb8bb L 11 3 B 6510-1989 Pneumatic pressure equipment Table 1 (Continued) Test item Oil hydraulic pressure equipment Test method Exami
19、ne the reliability of such functions as oil tightness and pressure regulation. Examine the reliability of such functions as air tightness and pressure regulation, Examine the reliability of functions. Remark: For a spindle moulding machine which is not provided with any functions concerned, the test
20、 items corresponding to these in Table 1 are to be omitted. 3. Methods for Running Tests 3.1 No Load Running Test Rotate the main spindle, continue running for 30 to 60 minutes, measure required electric powers and noise after bearing temperatures have been stabilized , record on respective items sp
21、ecified in Table 2 Record Format 1, and observe , at the same time , by the sense of touch that no abnormal vibration exists. Furthermore, the measurement of the noise shall be in accordance with JIS B 6521. Table 2. Record Format 1 No, Speeds of rotation of Temperatures OC min- Irpml Main spindle b
22、earings Left Right Left Right 1 S Required electric powers Left I Right Remarks 1. Regarding the spindle shaper moulding machine, records shall be filled in the left side columns of Record Format 1. 2. For a spindle moulding machine provided with the speed change device of the main spindle speed of
23、rotation, records shall be taken on at least 2 levels of speeds of rotation including the maximum speed of rotation. 3. Regarding the measuring conditions of noise, these shall be recorded in the description column. 3.2 Load Running Test Carry out the cutting of the test material, measure required e
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 6510 1989 R2004 ENG
链接地址:https://www.31doc.com/p-3782571.html