ISO-7816-9-2004.pdf
《ISO-7816-9-2004.pdf》由会员分享,可在线阅读,更多相关《ISO-7816-9-2004.pdf(20页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO/IEC 7816-9:2004(E) ISO/IEC 2004 INTERNATIONAL STANDARD ISO/IEC 7816-9 Second edition 2004-06-01 Identification cards Integrated circuit cards Part 9: Commands for card management Cartes didentification Cartes circuit intgr Partie 9: Commandes pour la gestion des cartes ISO/IEC
2、7816-9:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In download
3、ing this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the Gen
4、eral Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address give
5、n below. ISO/IEC 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs mem
6、ber body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2004 All rights reserved ISO/IEC 7816-9:2004(E) ISO/IEC 2004 All rights reserved i
7、ii Contents Page Forewordiv Introduction v 1 Scope1 2 Normative references .1 3 Terms and definitions.1 4 Abbreviations and notation1 5 Life cycle2 5.1 File life cycle2 6 Commands for card management.3 6.1 CREATE FILE command .3 6.2 DELETE FILE command3 6.3 DEACTIVATE FILE command.4 6.4 ACTIVATE FIL
8、E command.5 6.5 TERMINATE DF command.5 6.6 TERMINATE EF command.6 6.7 TERMINATE CARD USAGE command.7 Annex A (informative) Examples of security attributes used for download.8 Bibliography .12 ISO/IEC 7816-9:2004(E) iv ISO/IEC 2004 All rights reserved Foreword ISO (the International Organization for
9、Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective orga
10、nization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technol
11、ogy, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards
12、adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subjec
13、t of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 7816-9 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. This second edition, together with the s
14、econd editions of ISO/IEC 7816-4, ISO/IEC 7816-5, ISO/IEC 7816-6 and ISO/IEC 7816-8, after an in-depth reorganization of these five parts, cancels and replaces ISO/IEC 7816- 4:1995, ISO/IEC 7816-5:1994, ISO/IEC 7816-6:1996, ISO/IEC 7816-8:1999 and ISO/IEC 7816-9:2000. It also incorporates the Amendm
15、ents ISO/IEC 7816-4:1995/Amd.1:1997, ISO/IEC 7816-5:1994/Amd.1:1996 and ISO/IEC 7816-6:1996/Amd.1:2000 and the Technical Corrigendum ISO/IEC 7816-6:1996/Cor.1:1998. ISO/IEC 7816 consists of the following parts, under the general title Identification cards Integrated circuit cards: Part 1: Cards with
16、 contacts Physical characteristics Part 2: Cards with contacts Dimensions and location of the contacts Part 3: Cards with contacts Electrical interface and transmission protocols Part 4: Organization, security and commands for interchange Part 5: Registration of application providers Part 6: Interin
17、dustry data elements for interchange Part 7: Interindustry commands for Structured Card Query Language (SCQL) Part 8: Commands for security operations Part 9: Commands for card management Part 10: Cards with contacts Electronic signals and answer to reset for synchronous cards Part 11: Personal veri
18、fication through biometric methods Part 15: Cryptographic information application -,-,- ISO/IEC 7816-9:2004(E) ISO/IEC 2004 All rights reserved v Introduction ISO/IEC 7816 is a series of International Standards specifying integrated circuit cards and the use of such cards for interchange. These card
19、s are identification cards intended for information exchange negotiated between the outside world and the integrated circuit in the card. As a result of an information exchange, the card delivers information (computation result, stored data), and/or modifies its content (data storage, event memoriza
20、tion). Five parts are specific to cards with galvanic contacts and three of them specify electrical interfaces. ISO/IEC 7816-1 specifies physical characteristics for cards with contacts. ISO/IEC 7816-2 specifies dimensions and location of the contacts. ISO/IEC 7816-3 specifies electrical interface a
21、nd transmission protocols for asynchronous cards. ISO/IEC 7816-10 specifies electrical interface and answer to reset for synchronous cards. ISO/IEC 7816-12 specifies electrical interface and operating procedures for USB cards. All the other parts are independent from the physical interface technolog
22、y. They apply to cards accessed by contacts and/or by radio frequency. ISO/IEC 7816-4 specifies organization, security and commands for interchange. ISO/IEC 7816-5 specifies registration of application providers. ISO/IEC 7816-6 specifies interindustry data elements for interchange. ISO/IEC 7816-7 sp
23、ecifies commands for structured card query language. ISO/IEC 7816-8 specifies commands for security operations. ISO/IEC 7816-9 specifies commands for card management. ISO/IEC 7816-11 specifies personal verification through biometric methods. ISO/IEC 7816-15 specifies cryptographic information applic
24、ation. ISO/IEC 10536 specifies access by close coupling. ISO/IEC 14443 and 15693 specify access by radio frequency. Such cards are also known as contactless cards. -,-,- INTERNATIONAL STANDARD ISO/IEC 7816-9:2004(E) ISO/IEC 2004 All rights reserved 1 Identification cards Integrated circuit cards Par
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 7816 2004
链接地址:https://www.31doc.com/p-3782593.html