JIS-B-6518-1990-R2003-ENG.pdf
《JIS-B-6518-1990-R2003-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-6518-1990-R2003-ENG.pdf(16页珍藏版)》请在三一文库上搜索。
1、J I S 8*653 90 4933608 0036973 2 JIS e e I UDC 621.91 2.2-589.2.001.4 JAPANESE INDUSTRIAL STANDARD Test methods for performance and accuracy of moulding machine JIS B 6518-1990 Translated and Published by Japanese Standards Association Printed in Japan 9s Copyright Japanese Standards Association Pro
2、vided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 19:41:33 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S BXb5Ld 90 E 4933608 OULb974 4 = In the event of any doubt arising, the original Standard in Japa
3、nese is to be final authority. Q o O Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 19:41:33 MDTNo reproduction or networking permitted without license from IHS -,-,- UDC 621.912.2-589.2.0
4、01.4 JAPANESE INDUSTRIAL STANDARD J I S Test methods for performance and B 6518-1990 accuracy of moulding machine 1. Scope This Japanese ,;idustrial Standard specifies test methods for performance and rigidity, and inspection method for static accuracy and working accuracy of moulding machine. Remar
5、ks 1. 2. 3. 4. The moulding machine consists of rotating plural lateral plane shell, vertical plane shell (inclined plane shell) and automatic feed apparatus and means the planing and moulding machine which cuts an optional section shape by fixing the main table ( I ) , capable of travelling in righ
6、t and left, up and down or inclining the shell of plane and by feeding linearly the work pieces. The applicable Standards to this Standard are shown in the following: JIS B 6507-General Code of Safety for Woodworking Machinery JIS B 6521-Method of Measurement for Noise Emitted by Woodworking Machine
7、ry The corresponding International Standard to this Standard is shown as follows. IS0 7947-Woodworking machines - Two-, three- and four-side moulding machines - Nomenclature and acceptance conditions In this Standard the units and numerical values shown in are in accordance with traditional units an
8、d, appended for informative reference. Note () In case where the main table is not independent, it means the surface place total body. Function Test Methods The function tests of moulding machine shall be in accordance with Table 1. Reference Standards: JIS B 6501-Test Code for Performance and Accur
9、acy of Wood Working Machinery JIS Z 8203-SI Units and the Use of their Multiples and of Certain other Units Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 19:41:33 MDTNo reproduction or ne
10、tworking permitted without license from IHS -,-,- Test item Measuring method Operations of right- and-left travelling, up-and-down travelling, and clamping as well as automatic stopping opera tion Move the main shaft in right-and-left, up-and-down or incline, test the smoothness and uniformity of ac
11、tuation over the whole length of moving, and at the middle and both ends of moving, test the security of clamping and smooth- ness of actuation of clamping apparatus. Further, at both ends of moving, test the smoothness and security of actuation of automatic stopping apparatus. Actuating operation o
12、f movable part Relative to the movable range of moving, test the security and smoothness of actuation. Safety device Test the security of safety function and machine-protective function to the worker (Refer to JIS B 6507). 2 B 6518-1990 Table 1. Function Test Num- ber 1 Electric apparatus Before and
13、 after operating test, carry out the insulation condition test each once. At a suitable rotary speed of main shaft, repeat the starting and stopping ten times and test the smoothness and security of actuation. Relating to all marked rotary speeds convert the main shaft rotary speed, and test the smo
14、othness of actuation of operating apparatus and security of indication. 2 Starting, stopping and of main shaft and running operation 3 Converting operation of rotary speed of main shaft 4 Starting, stopping and running operation of carriage At a suitable feed speed, carry out the starting, stopping
15、repeatedly ten times, and test smoothness and security of actuation. 5 Converting operation of feed speed Convert the speeds relating to marked all feed speeds and three feed speeds of the lowest, medium and the highest, test the smoothness of actuation and security of indication of operation appara
16、tus. 6 Operation of hand feed Test the smoothness and uniformity of actuation over the whole length of motion according to hand feed handle, and rotate the micro-hand-feed handle several times and test the smoothness and uniformity. 7 8 9 Attaching and detach- ing of plane blade and cutter Pressuriz
17、ing apparatus Test the smoothness and security of attaching and detaching of plane blade and cutter as well as of fastening screws. 10 Test the smoothness and security of function. 11 12 Lubricating apparatus Test the security of function such as oil tightness, suitable distribution of oil quantity,
18、 etc. Test the security of function such as oil tightness, pressure regulation, etc. 13 Oil hydraulic apparatus Pneumatic apparatus 14 Test the security of function such as air tightness, pressure regulation, etc. 15 Accessories I Test the security of function. Remark: In a moulding machine without
19、the function, the test item corresponding thereto in Table 1 is omitted. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 19:41:33 MDTNo reproduction or networking permitted without license
20、from IHS -,-,- J I S B*b518 90 4733bU8 003b97 T I 3 B 6518-1990 0 3. Running Test Method 3.1 No-load Running Test Rotate each main shaft, continue the running for 30 to 60 min, after the bearing temperature has been stabilized, measure the required electric power and noise, and record relating to ea
21、ch item specified in Record Format 1 of Table 2 as well as observe that there is no abnormal vibration by feeling. Further, measure the noise according to JIS B 6521. Table 2. Record Format 1 Num- ber Meas- I uring time Name of plane shell h min I Upper lateral plane shell Right vertica plane shell
22、1 Required elec- Temperature “C tric power Rotary speed of main shaft Noise dB (A) zur- In- rent put A kW - Descrip- tion Remarks 1. In the case where speed change gear of rotary speed of main shaft, record relating to rotary speed of at least two levels containing the maximum rotary speed. Relating
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 6518 1990 R2003 ENG
链接地址:https://www.31doc.com/p-3782639.html