ISO-9455-15-1996.pdf
《ISO-9455-15-1996.pdf》由会员分享,可在线阅读,更多相关《ISO-9455-15-1996.pdf(14页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 9455-15 First edition 1996-09-01 Soft soldering fluxes - Test methods - Part 15: Copper corrosion test Flux de brasage tendre - MBthodes dessai - Partie 7 5: Essai de corrosion du wire Reference number IS0 9455-l 5:1996(E) Copyright International Organization for Standardi
2、zation Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 20:45:15 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 9455-15:1996(E) Foreword IS0 (the International Organization for Standardization) is a worldw
3、ide fed- eration of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on
4、that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted
5、 by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 9455-15 was prepared by Technical Com- mittee ISO/TC 44, Welding and allied process
6、es, Subcommittee SC 12, Soldering and brazing materials. IS0 9455 consists of the following parts, under the general title Soft soldering fluxes - Test methods: - Part 1: Determination of non-volatile matter, gravimetric method - Part 2: Determination of non-volatile matter, ebulliometric method - P
7、art 3: Determination of acid value, potentiometric and visual titration methods - Part 5: Copper mirror test - Part 6: Determination of halide (excluding fluoride) content - Part 8: Determination of zinc content - Part 9: Determination of ammonia content - Part IO: Flux efficacy tests, solder spread
8、 method - Part 1 I: Solubility of flux residues - Part 12: Steel tube corrosion test 0 IS0 1996 All nghts reserved. Unless otherwrse specified, no part of this publicatron may be reproduced or utrlized In any form or by any means, electronic or mechanical, including photocopying and microfilm, witho
9、ut permrssron in wrtting from the publisher. International Organrzatron for Standardization Case Postale 56 ? CH-1211 Geneve 20 ? Switzerland Pnnted in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9
10、972545001 Not for Resale, 04/22/2007 20:45:15 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 IS0 9455-15:1996(E) - Part 13: Determination of flux spattering - Part 14: Assessment of tackiness of flux residues - Part 15: Copper corrosion test - Part 16: Flux efficacy te
11、sts, wetting balance method - Part 17: Surface insulation resistance comb test and electrochemical migration test of flux residues Annex A of this part of IS0 9455 is for information only. III Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NA
12、SA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 20:45:15 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD 0 IS0 IS0 9455-15:1996(E) Soft soldering fluxes - Test methods - Part 15: Copper corrosion test 1 Scope This part of IS0 9455 speci
13、fies a qualitative method for determination of the corrosive properties of flux residues on a copper substrate, when subjected to controlled environmental conditions. The test is appli- cable to type 1 fluxes, as defined in IS0 9454-l 2 Normative references The following standards contain provisions
14、 which, through reference in this text, constitute provisions of this part of IS0 9455. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 9455 are encouraged to investigate the possibility of appl
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 9455 15 1996
链接地址:https://www.31doc.com/p-3782714.html