JIS-B-0411-1978-R2003-ENG.pdf
《JIS-B-0411-1978-R2003-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-0411-1978-R2003-ENG.pdf(6页珍藏版)》请在三一文库上搜索。
1、. J I S B 8 4933608 00083LO 2 m UDC /- 669-138.8:621.753.1 JAPANESE I NDUSTRIAL STANDARD Permissible Deviations in Dimensions without Tolerance Indication for Metallic Sintered Products JIS B 04 I I -1978 Translated and Published by Japanese Standards Association Printed in Japan 4 s Copyright Japan
2、ese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:15:56 MSTNo reproduction or networking permitted without license from IHS -,-,- Translation without guarantee standard in Japanese is to be evidence i n
3、the event of any doubt arising, the original Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 07:15:56 MSTNo reproduction or networking permitted without license from IHS -,-,- t ? JAPANESE
4、INDUSTRIAL STANDARD J I S Permissible Deviations i n Dimensions without Tolerance Indication for Metallic Sintered Products B 0411-1978 1. Scope This Japanese Industrial Standard specifies the permissible devia- tions i n dimensions without tolerance indication t o be applied t o working dimensions
5、(1) of the metallic sintered products, i n particular, sintered machine parts and o i l impregnated sintered bearings. 1 Note ( ) The working dimensions herein mentioned imply those peculiar t o the metallic sintered products t o the exclusion of other working dimensions such as those made by cuttin
6、g, Remarks 1. The permissible deviations i n dimensions without tolerance indication shall be indicated not individually but i n a limp i n specifications, drawings, etc. for the dimensions which require no particular functional accuracy. 2. The permissible deviations i n dimensions without toleranc
7、e indication shall be indicated i n accordance either with (1) or with (2) below. (1) Table giving individual numerical values t o dimensional divisions. (2) The number of t h i s standard and the grade specified in t h i s standard. Example: J I S B 0411, Fine grade Reference Standards: JIS B 0404-
8、General Rules for permissible Deviations i n Dimensions without Tolerance Indication IS0 2768-:Permissible machining variations i n dimensions without tolerance indication Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Ber
9、nie Not for Resale, 03/10/2007 07:15:56 MSTNo reproduction or networking permitted without license from IHS -,-,- 2 J I S B*O421 78 I 4733b08 OU83113 8 B 0411-1978 2. Definitions The principal terms used in this standard are as defined below. (1) width Dimension perpendicular to the compression dire
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 0411 1978 R2003 ENG
链接地址:https://www.31doc.com/p-3782719.html