《JIS-B-6571-1992-R2004-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-B-6571-1992-R2004-ENG.pdf(39页珍藏版)》请在三一文库上搜索。
1、J I S B*b571 92 m 4933608 0511129 365 m UDC 003:674.05-589 JIS JAPANESE INDUSTRIAL STANDARD Numerically control led woodworking machines - Marking symbols for operations JIS B 6 5 7 1 - 1 9 9 2 CI f Translated and Published by Japanese Standards Association Printed in Japan 20 s Copyright Japanese S
2、tandards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- In thc cvcnt of any doubt arising, the original Standard in Japancse is to be
3、final authority. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- I J I S B*b571 72 4733608 0511131 TL3 m U
4、DC 003: 674.05-589 JAPANESE INDUSTRIAL STANDARD J I S Numerically controlled woodworking machines B 6571-1992 - Marking symbols for operations 1. Scope marking the operations and matters relating to operations of numerically controlled woodworking machines , as well as the definitions thereof. This
5、Japanese Industrial Standard specifies the symbols to be used for Remarks: The woodworking machines mean the machines which remove the unnecessary parts from the work pieces of wood and woody materials by cutting, grinding and the like to make up into the required shapes and profile irreguhrities, h
6、owever, in this Standard, saw finishing machines and tool grinders for woodworking machines are also included. 2. Methods for using symbols operations (in particular, for warnings and restriction of uses). 2 . 1 General It should be preferable to use symbols for the markings of 2.2 Shapes of symbols
7、 The symbols illustrated in this Standard shail be those for specifying the basic shapes, but not for specifying the sizes and dimensions thereof. In the case of actual application, it should be preferable to use those which are similar to those as illustrated. the following: Furthermore, the arrow
8、marks of symbol shall be in accordance with (i) The pointed end angle of the arrow marks indicating the moving direction of linear motion, rotary motion and the like shall be 30. (2) The arrow marks indicating the operations of clamping, unclamping, mounting, dismounting, and the like shall be 60 or
9、 over in pointed end angle, and the shafts shall be thick and short. 2.3 Combination of symbols The symbols may also be used combining appropriately , as required. 3. Classification The classification of symbols shall be in accordance with the following: (1) Forms of motion (a) Rectilinear motion an
10、d rotation (b) Feed motion (c) Cutting motion Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S E*b5?1
11、i Si! W 4933b08 05BI1132 S5T W 2 B 6571-1992 (2) Objective elements of operation (a) Work piece and machine component (b) Spindle and quill (3) Operations (a) Operations in general (b) Mounting and dismounting and engaging and disengaghg (c) Other operations (4) Safety devices and caution (5) Machin
12、e in general (a) Lubrication, oil hydrauXcs and cutting fluid (b) Measurements (c) Others (6) Numerical control (a) Data carrier and program (b) Numerical control functions 4. Symbols The symbols and definitions thereof shall be in accordance with the following: Copyright Japanese Standards Associat
13、ion Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S BS6571 92 = 4933608 0511133 896 3 B 6571-1992 (i) Forms of motions (a) Rectilinear motion
14、s and rotation - No. 10 1 10 2 103 104 105 106 107 108 Symbol - 4 Definition Direction of rectilinear motion Remarks: When the direction of motion is in opposite direction - may ais0 be permissi- ble. Rectilinear motion in two directions Interrupted rectilinear motion Remarks: When in two directions
15、 -* Rectilinear motion to the limited position that stops at the end position Remarks: When limited in two directions t+-d One reciprocating rectilinear motion between the limited positions that stops after one round trip Oscillating rectilinear motion (continuous) Remarks: When the last limited pos
16、ition lies beyond the returning point. EL Direction of continuous rot atiori Rotation in two directions E quivalen t English (Informative reference) iirection of continuous rectilinear motion rectilinear motion in two directions nterrupted rectilinear motion imited rectilinear motion imited rectilin
17、ear motion and return 3scillating rectilinear motion (continuous) lirection of continuous rotation rotation in two directions Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo
18、reproduction or networking permitted without license from IHS -,-,- J I S B*h571i 92 W Y933608 055hb3Y 722 4 B 6571-1992 No. 7 109 L_ 110 111 112 - 113 I I Equivalent Symbol I Definition I reference) I direction of Direction of internmted rotation T“rections interrupted rotation -a ! I i 9 1 limited
19、 that stops at the end foint Remarks: When stops in two 1 rotation l i directions Reciprocating rotation between Bmited the limited positions that stops I ! rotation and after one round trip i return Continuous oscillating rotary I oscillating motion i rotary motion Remarks: In the case where the !
20、(con- tinuous) last stopping position . Ees beyond the returning point I t Direction of spindle rotation direction of . spindle Remarks 1. When an interrupted , rotation rotary motion 1 i 2. In the case of a spindle, it may be substituted for the symbol of objective spindle Copyright Japanese Standa
21、rds Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*b5?1 92 Y933608 0511135 669 Revolution 5 B 6571-1992 reference) revolution
22、No. 114 1 115 0 116 117 Symbol o o o X r n i n- Definition I Equivalent Remarks: In the case where the revolution in a con- tinuous revolution is of a counter clockwise revolution One revolution one revolution ! I j oriented stop Revolution that stops at the limited position i i i j I number of I Nu
23、mber of revolutions per minute I revolutions I Remarks: X being the numerical I per (spindle minute I speed) value of revolutions, as the case may be, either not be used, or be arranged in a table. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/
24、1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- JIS B*b571i 72 W 4933b08 0551ib3b 5T5 m 6 B 6571-1992 No. - 121 - 122 II 123 124 125 - 126 - 127 (b) Feed motions Symbol I Esuivalent Definition reference) Feed
25、 feed I I Feed per revolution i feed per I value of the feed, as i the case may be, either ! not be used, or be arranged in a table. revolution Remarks: )i being the numerical I Feed per minute 1 feed per I minute I i i Low speed feed, reduced feed i reduced feed ! h Remarks: l/X being the ratio I E
26、nglish (Informative of reduced speed to the normal feed, it may not be used. Normal feed Remarks: l/l may not be used. normal feed Rapid feed, speed increasing feed Remarks: X/l being the ratio of increased speed to the normal feed, it may not be used. rapid feed Longitudinal feed I longitudinal Rem
27、arks: When the direction of feed is indicated w I feed when an operational object is appended Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permi
28、tted without license from IHS -,-,- J I S Bab571 92 W 4933608 0511137 431 m 7 B 6571-1992 - No. - 128 129 130 13 1 132 S-ymbol Definition Transverse feed Remarks: When the direction of feed is indicated when an operational object is appended Vertical feed Remarks: When the direction of feed is indic
29、ated when an operational object is appended Rapid traverse Feed per stroke Remarks: When feed is made only at one end of stroke I Feed per stroke mm Remarks: X being the numerical value of feed at every stroke, it may be, either not be used or be arranged in a table. Equivalent English (Informative
30、reference 1 trans vers e feed vertical feed rapid traverse feed per stroke feed per stroke mm Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permi
31、tted without license from IHS -,-,- J I S Bab571 92 Y933608 0551538 378 8 B 6571-1992 No. 133 134 c _ _ 135 - 136 Symbol + o Definition _ _ Increase of value Remarks: In the marking of high speed range (revo- lution), may also be used. Decrease of value Remarks: In the marking of low speed range (re
32、vo- lution), may also be used. Tarry Dwell Equivalent English (Informative reference) increase of value (speed, for instance) decrease of value (speed, for inst ance) tarry dwell Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wi
33、ng, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*b571 72 4733608 0511137 204 9 B 6571-1992 (c) Cutting motions No. - 151 152 15 3 15 4 155 Symbol k De finition Threading Remarks: When a left-hand thread is shown Out-side
34、 turning Remarks: When a cutting speed is shown In-side turning Remarks 1. When a cutting speed is shown 2. When the work piece rotates Drilling Remarks: When a cutting speed is shown Up milling Remarks: When a cutting speed is shown Equivalent English (Informative reference) threading out -side tur
35、ning in-side boring turning y drilling y boring up milling Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,-
36、 10 B 6571-1992 No 156 - 157 158 15 9 16 O Symbol Definition Down milling Remarks: When a cutting speed is shown Grinding, sanding or polishing Remarks 1. As required, the grindingstone may also be substituted for other simple one which is similar and nearly the same as an actual shape. is shown 2.
37、When a cutting speed i R E s : When a cutting speed is shown i ! Chain mortising Remarks: When a cutting speed is shown Il. II XmLs - Mortising Remarks: When a cutting speed is shown Equivalent English (Informative reference) down milling grinding, sanding , polishing honing chain mortising mor ti s
38、ing Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- No. 161 162 163 J I S B*b571 92 W 4933608 0511141 962
39、11 B 6571-1992 Symbol De fi nit ion Circular sawing Remarks: When a cutting speed is shown Band sawing Remarks: When a cutting speed is shown 4 % Xm/s Planing Remarks When a cutting speed is shown Equivalent English (Informative reference) circular sawing band sawing planing , moulding Copyright Jap
40、anese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- 12 B 6571-1992 t Definition Symbol i (2) Objective elements for operati
41、ons (a) Work pieces and machine components Equivalent English (Informative No rotating element 201 Jaw clutch or gear clutch Remarks: A clutch in which claws, gears on the like interlock. 202 jaw clutch, gear clut ch 203 7 204 205 _ I 206 207 - i i reference) a I work I I I rectangular I work table
42、! or slide i element l : Rectangular work table I I i I i rectangular Rectangular work table with magnetic chuck table with t magnetic Remarks: Not limited to be used I chuck i i piece. I for mounting work Round work table Vacuum work table vacuum work table I I Friction clutch Copyright Japanese St
43、andards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*b571 72 W 4933608 0511143 735 13 B 6571-1992 Definition Equivalent Engl
44、ish (Informative reference) chuck No. Symbol 208 Chuck E 209 Spring collet spring collet I- - 210 tracer Tracer Remarks: The direction of the tracer may be adjusted to the actual circum- stances. Electric motor 211 electric motor 212 o Pump 2 13 o Coolant pump coolant pump 214 lubricant Pump 8 Lubri
45、cant pump 215 Hydraulic system pump hydraulic system pump Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 19:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,-
46、JIS B*b5?L 92 W 4933b 055311114 b 5 m 14 B 6571-1992 No. I Symbol I Equivalent Definition reference) HydrauEc motor , hydraulic Vacuum pump No 231 232 233 234 Symbol 111 4 - h t d L Y i motor I I (b) Spindles and quills De f i n i tion Spindle Remarks: As required the symbol may as0 be substituted f
47、or other simple one which is similar and nearly the same as the actual shape. Quiii Remarks: As required the symbol may also be substituted for other simple one which is similar and nearly the same as the actual shape. Drilling spindle Remarks: As required the symbol may also be substituted for other simple one whichis similar and nearly the same as the actual shape. Shaping spindle Equivalent English (Informative reference) spindle quill drilling spindle, boring spindle shaping spindle Copyright Japanese Standar
链接地址:https://www.31doc.com/p-3783249.html