JIS-C-9605-1988-R2005-ENG.pdf
《JIS-C-9605-1988-R2005-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-C-9605-1988-R2005-ENG.pdf(26页珍藏版)》请在三一文库上搜索。
1、IJIS C*bO5 88 I 4933608 0039574 4 W * I- +-= JAPANESE INDUSTRIAL STANDARD Portable Electric Drills UDC 621.953-83 Translated and Published by Japanese Standards Association Printed in Japan 14 S Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/111
2、1111001, User=Wing, Bernie Not for Resale, 03/15/2007 19:36:32 MDTNo reproduction or networking permitted without license from IHS -,-,- In the event of any doubt arising, the original Standard in Japanese is to be final authority. Copyright Japanese Standards Association Provided by IHS under licen
3、se with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 19:36:32 MDTNo reproduction or networking permitted without license from IHS -,-,- JI C*b05 88 m 4933608 O039576 8 Class Nominal size of maximum diameter of. drill . mm output W UDC 62 1.953-83 5 mm 6.5 mm 10
4、mm 13 mm 16 mm 20 mm 25 mm 32 mm 5 6.5 10 13 16 20 25 32 55 75 150 225 260 370 600 1000 min. min. min. min. min. min. min. min. JAPAN ES E IN DUSTRIAL STAN DARD J I S Portable Electric Drills C 9605-1988 Class 21 mm I 1. Scope 24 mm 30 mm 36 mm This Japanese Industrial Standard specifies metal porta
5、ble electric drills and wood portable electric drills of rated frequency 50 Hz only, 60 Hz only or 50/60 Hz in common, hereinafter referred to as the “electric drills“. in this Standard are Remark: The units and numerical values shown in based on the traditional unit system, and are appended for inf
6、ormative reference Nominal size of maximum diameter of drill mm 2. Classification on Output The electric drills are classified according to the maximum value of usable The time drill diameter, and the outputs, corresponding to the classes, shall be as given in Table 1 for metal drills and as given i
7、n Table 2 for wood drills. rating of motor shall be 30 min. 21 output W Table 2. Classification and Output of Wood Electric Drill 135 160 190 220 min. min, min. min. 24 30 36 3. Rated Voltage and Driving Motor The classification and the rated voltages of electric drill driving motors shall be as giv
8、en in Table 3. Applicable Standards: See page 23. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 19:36:32 MDTNo reproduction or networking permitted without license from IHS -,-,- !JI$ C*b
9、05 88 W Y933608 O039577 T W I c 2 C 9605-1988 Table 3. Classification and Rated Voltage of Driving Motor Unit: V Classification of driving motors Rated voltage 100 or 200 Series commutator motor or single-phase induction motor Three-phase squirrel-cage induction motor 200 4 . Fluctuation of Operatin
10、g Voltage The electric drill shall be capable of being used without practical trouble even if the supply voltage at its terminals changes above and below its rated voltage by 10 %. 5. Performances 5,l Starting The drill shall start irrespective of its motor rotor position when the test of 8.2 is car
11、ried out. 5.2 Run Out of Drill Bit Tip The run out of drill bit tip, tested as specified in 8.3, shall not exceed the relevant value of Table 4 every time. Table 4 . Run Out of Drill Bit Tip Unit: mm Mounting of drill chack Run out of drill bit tip Taper type 0.3 Screw type 0.6 I 5.3 Temperature The
12、 temperatures of various parts tested as specified in 8.4 shall not exceed the relevant values of Table 5. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 19:36:32 MDTNo reproduction or net
13、working permitted without license from IHS -,-,- JIS C*9605 88 m 4933608 0039578 I m Measurement position Of class A insulation 3 C 9605-1988 Temperature 105 Table 5. Temperature Limit Unit: “C Of class F insulation Of class H insulation 140 165 Motor winding Knob of switch, push button 1 Of class E
14、 insulation I 120 Of metal, ceramics or glass 60 Of others 75 I Of class B insulation I 125 Accessible enclosure (including gear case and bearing part) Of metal, ceramics or glass 65 Of others 80 Handle operated by a man during service Of metal, ceramics or glass 55 Of others 70 Kind of insulation B
15、asic insulation Remark: The ambient temperature is 30C Insulation resistance 2 5.4 Insulation The. insulation shall comply with the following requirements: Supplementary insulation Reinforced insulation ( 1 ) Insulation Resistance The insulation resistance tested as specified in 8.5 (1) shall be not
16、 less than 2 Ma for drills of other construction than class II insulation specified in 6.7, and 7 n for ones of class II insulation. of class II insulation, the insulation resistances shall have at least the relevant values given in Table 6. If the measurement is carried out on each kind of insulati
17、on for drills Table 6. Insulation Resistance 5 7 Unit: M a Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 19:36:32 MDTNo reproduction or networking permitted without license from IHS -,-,-
18、 JIS C*9bO5 8 W 4933608 0039579 3 W - * 4 C 9605-1988 (2) Dielectric Withstand Voltage The drills shall withstand the test voltage when the test of 8.5 (2) is carried out. 5.5 Output The output shall comply with the following requirements: (1) The outputs shall be as given in Table 1 or Table 2, whe
19、n the test of 8.6 (1) is carried out, The current shall not exceed 110 % of the full load current (current entered in the nameplate), when the test of 8.6 (2) is carried out. 5.6 Switch The switches shall comply with the following requirements: (2) (1) No trouble shall be caused at any part when a s
20、witch is subjected to the test of 8.7 (1). The temperature of contact shall not exceed the relevant value given in Table 7 when a switch is subjected to the test of 8.7 (2). (2) Table 7. Temperature Limit of Contact Unit: “C Kind of contact Temperature Copper or copper alloys 70 Silver or silver all
21、oys 95 Remark: The ambient temperature is 30C 5.7 Flexure of Cord 5.7.1 body and cord shall not cause short circuit of the cord when subjected to the test of 8.8.1. Flexure of Joint between Body and Cord The joint between appliance Further, the rate of broken component wires shall not exceed 10 %. 5
22、.7.2 Flexure of Joint of Cord in Non-renewable Connector with Cord The ioint of cord in a non-renewable connector with cord shall not cause short circit of the cord when subjected to the test of 8.8.2. Further the rate of broken component wires shall not exceed 20 %. 5.8 Resistance to Shock The resi
23、stance to shock tested as specified in 8.9 shall comply with the following requirements: (1) No live parts shall be exposed. a degree that the live part is not touched by the test finger when tested by the test finger shown in Attached Figure, is an exception. However, exposure of live part in such
24、(2) No short circuit shall occur when the electric drill is connected to the power supply. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 19:36:32 MDTNo reproduction or networking permitte
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 9605 1988 R2005 ENG
链接地址:https://www.31doc.com/p-3784087.html