JIS-C-2805-2003-ENG.pdf
《JIS-C-2805-2003-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-C-2805-2003-ENG.pdf(29页珍藏版)》请在三一文库上搜索。
1、JAPANESE INDUSTRIAL STANDARD JIS C 2805 : 2003 Crimp-type terminal lugs for copper conductors March, 2004 ERRATA Page 3 4.11, 4.14, 4.16 Error : 4.9 Correct: 4.10 Page 18 In the blank box below F(13, “Min.” is inserted. In the column of tolerance for dl, delete the line as follows: Page 19 In Attach
2、ed Table 1, the value of Tolerance for D for stranded wire of nominal sectional area 325 mm2 is changed as follows: Error: +1.0 Correct: +1.0 0.6 -0.6 Page 22 In Attached Table 4, in the column of “Dimensions of non-insulated terminal lug, Bt0.2”, the line below the value 8.0 is deleted. Remarks: Th
3、is erratum is for correcting the first edition of this Standard. Japanese Standards Association - 7 - Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 02:27:02 MDTNo reproduction or networki
4、ng permitted without license from IHS -,-,- J IS JAPANESE I N DUSTR IAL STANDARD Translated and Published by Japanese Standards Association Crimp-type terminal lugs for copper conductors ICs 29.120.20 Reference number : JIS C 2805 : 2003 (E) PROTECTED BY COPYRIGHT 15 S Copyright Japanese Standards A
5、ssociation Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 02:27:02 MDTNo reproduction or networking permitted without license from IHS -,-,- C 2805 : 2003 Foreword This translation has been made based on the original Japanese Ind
6、ustrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Electrical Manufacturers Association (JEMA) with the draft being
7、 attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14, Consequently JIS C 2805 : 1991 is replaced with this Standard. Date of Establishment: 1969-07-01 Date of Revision: 2003-06-20 Date of Publ
8、ic Notice in Official Gazette: 2003-06-20 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Electricity Technology JIS C 2805 : 2003, First English edition published in 2003-10 Translated and published by: Japanese Standards Association 4-1-24, Akasaka,
9、Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mech
10、anical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 02:27
11、:02 MDTNo reproduction or networking permitted without license from IHS -,-,- C 2805 : 2003 Contents Page 1 2 3 4 4 . 1 4.2 4 . 3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4 . 1 5 4.16 5 6 6.1 6.2 7 7.1 Scope Normative references Classification. symbol and nominal size . Performance Securenes
12、s of crimped connection Temperature rise . Cyclic heating . Electrical resistance Salt spray Withstanding overcurrent Tensile strength . Vibration fatigue Insulation resistance . Dielectric withstand voltage Resistance to thermal aging Secureness of insulation . Flame retardance . Resistance to oil
13、. Restitution Cold crimping property . Appearance. dimensions and metallic coating . Materials and machining method . Materials . Machining method . Test method Testing conditions 1 1 1 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Prov
14、ided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 02:27:02 MDTNo reproduction or networking permitted without license from IHS -,-,- C 2805 : 2003 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19 7.20 Ap
15、pearance test . Dimension test . Thickness test for metallic coating Secureness test of crimped connection Temperature rise test . Cyclic heating test . Electrical resistance test Salt spray test Withstanding overcurrent test Tensile strength test . Vibration fatigue test Insulation resistance test
16、. Dielectric withstand voltage test Aging test Insulation secureness test Flame retardance test . Oil immersion test . Restitution test Cold crimping property test . 6 7 8 9 10 10 11 11 12 13 13 13 14 14 14 15 8 Inspection 15 8.1 Type inspection 15 8.2 Acceptance inspection . 16 9 Designation of pro
17、duct . 17 10 Marking . 17 10.1 Marking on product . 17 10.2 Marking on package 17 (ii) PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 02:27:02 MDTNo reproduction or
18、networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS C 2805: 2003 Crimp-type terminal lugs for copper conductors 1 Scope This Japanese Industrial Standard specifies non-insulated crimp-type terminal lugs which are crimped directly, and insulated crimp-type terminal lu
19、gs which are crimped through their insulation (hereafter referred to as “non-insulated terminal lugs” and “insulated terminal lugs”, respectively, and as “terminal lugs” for both types in generic term) which are intended for connection of annealed copper stranded or solid wires principally used as i
20、nternal wiring of electric power machines and apparatus, and the wiring between the such machine and apparatus, in such a manner that the terminal lugs are connected to the ends of wires using the connect- ing tools specified in JIS C 9711 or those assigned by the terminal lug manufac- turer (hereaf
21、ter referred to as “tools”). Remarks : The insulated terminal lugs specified in this Standard are those used for wiring of control circuits or the like. 2 Normative references The following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard
22、. The most recent editions of the standards (including amendments) indicated below shall be applied. JIS B 4650 JIS B 7507 JIS C 1302 JIS C 1602 JIS C 2320 JIS C 3307 JIS C 9711 JIS H 3100 JIS H 8501 JIS H 8619 JIS K 2240 JIS Z 2371 JIS Z 3261 JIS Z 3264 JIS Z 8703 JIS Z 8704 Torque wrenches Vernier
23、, dial and digital callipers Insulation resistance testers Thermocouples Electrical insulating oils 600 V Polyvinyl chloride insulated wires Compression tools for wire connectors of interior wiring Copper and copper alloy sheets, plates and strips Methods of thickness test for metallic coatings Elec
24、troplated coatings of tin Liquefied petroleum gases Methods of salt spray testing Silver brazing filler metals Copper phosphorus brazing filler metals Standard atmospheric conditions for testing Temperature measurement-Electrical methods 3 Classification, symbol and nominal size The classification,
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 2805 2003 ENG
链接地址:https://www.31doc.com/p-3784208.html