JIS-R-6211-11-2003-R2008-ENG.pdf
《JIS-R-6211-11-2003-R2008-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-R-6211-11-2003-R2008-ENG.pdf(7页珍藏版)》请在三一文库上搜索。
1、JIS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS R 62 1 1 - 1 1 2003 (IS0 603- 1 1 : 1999) ( GTWJSA) Bonded abrasive products - Dimensions - Part 11 : Hand finishing sticks ICs 25.100.70 Reference number : JIS R 6211-11 : 2003 (E) PROTECTED BY COPYRIGHT
2、 5 s Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 03:35:38 MDTNo reproduction or networking permitted without license from IHS -,-,- R 6211-11 : 2003 (IS0 603-11 : 1999) Foreword This tran
3、slation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with the proposal of revising a Japanese Industrial Stan- dards from the Japan Grinding W
4、heel Association (GIS)/the Japanese Standards Association (JSA), with a draft of Industrial Standard based on the provision of Article 12 Clause 1 of the Industrial Standardization Law which shall be applied by Article 14 of the same Law. Conse- quently J I S R 6211-11:1999 is replaced with JIS R 62
5、11-11:2003. In this revision, IS0 603-11:1999 Bonded abrasive products-Dimensions-Part 11: Hand fin- ishing sticks is used as a basis to make Japanese Industrial Standard to conform to the corre- sponding International Standard. Attention is drawn to the possibility that some parts of this Standard,
6、 which have technical prop- erties, may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public. The Minis- ter of Economy, Tradc and Industry and the Japanese Industrial Stan
7、dards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utiiity model after opening to the public which have the said technical properties. JIS R 6211 consists of the following
8、16 parts under the general title Bonded abrasive products- Dimensions. Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for centerless external Cylindrical grinding Part 3: Grinding wheels for internal cylindrical grinding Part 4: Grinding wheels for
9、surface grindingiperipheral grinding Part 5 : Grinding wheels for surface grindingiface grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Part 8: Grinding wheels for deburring and fettlingisnagging Part 9: Grinding wheels for high-p
10、ressure grinding Part 1 O: Stones for honing and superfinishings Part 1 i: Hand fishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring and fettling on a vertical grinder Part 14: Grinding wheels for deburring and fettlingsnaggi
11、ng on an angle grinder Part 15: Grinding wheels far cutting-off on stationary ar mobile cutting-off machines Part 16: Grinding wheels for cutting-off on hand held power tools Date of Establishment: 1999-02-20 Date of Public Notice in Official Gazette: 2003-03-20 Investigated by: Japanese Industrial
12、Standards Committee Standards Board Technical Committee on Ceramics JIS R 62 1 1 - 1 1 : 2003, First English edition published in 2004-0 1 Translated and published by: Japanese Standards Association 4- 1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the conte
13、nts, the original JIS is to be the final authority. O JSA 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from th
14、e publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 03:35:38 MDTNo reproduction or networking permitted without license from IHS -,-,- R 6211-
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 6211 11 2003 R2008 ENG
链接地址:https://www.31doc.com/p-3785626.html