JIS-R-6211-10-2003-R2008-ENG.pdf
《JIS-R-6211-10-2003-R2008-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-R-6211-10-2003-R2008-ENG.pdf(9页珍藏版)》请在三一文库上搜索。
1、JIS JAPANESE I N D USTRIAL STANDARD Translated and Published by Japanese Standards Association (GIS/JSA) Bonded abrasive products - Dimensions - Part I O : Stones for honing and superfinishings ICs 25.100.70 Reference number : JIS R 6211-10 : 2003(E) PROTECTED BY COPYRIGHT 6 s Copyright Japanese Sta
2、ndards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 05:26:55 MDTNo reproduction or networking permitted without license from IHS -,-,- R6211-10 2003 Foreword This translation has been made based on the original Japane
3、se Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with the proposal of revising a Japanese Industrial Stan- dard from the Japan Grinding Wheel Association (G1S)the Japanese Standards Associ
4、ation (JSA), with a draft of Industrial Standard based on the provision of Article 12 Clause 1 of the Industrial Standardization Law which shall be applied by Article 14 of the same Law. Conse- quently JIS R 6211-10:1999 is replaced with JIS R 6211-10:2003. In this revision, IS0 603-10:1999 Bonded a
5、brasive products -Dimensions -Part 10: Stones for honing and superfnishings is used as a basis to make Japanese Industrial Standard to conform to the corresponding International Standard. Attention is drawn to the possibility that some parts of this Standard, which have technical properties, may con
6、flict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public. The Minister of Economy, Trade and Industry and the Japanese Industrial Standards Commit- tee are not responsible for ide
7、ntifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical properties. JIS R 6211 consists of the following 16 parts under the general title Bonded abr
8、asive products - Dimensions. Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for centerless external cylindrical grinding Part 3: Grinding wheels for internal cylindrical grinding Part 4 : Grinding wheels for surface grinding/peripheral grinding Part
9、 5: Grinding wheels for surface grindinglface grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Part 8: Grinding wheels for deburring and fettlinghnagging Part 9: Grinding wheels for high -pressure grinding Part 10: Stones for honin
10、g and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring and fettling on a vertical grinder Part 14: Grinding wheels for deburring and fettlingknagging on an angle grinder Part 16: Grinding w
11、heels for cutting-off on stationary or mobile cutting-off machines Part 16: Grinding wheels for cutting-offon hand held power tools Date of Establishment: 1999-02-20 Date of Revision: 2003-03-20 Date of Public Notice in Official Gazette: Investigated by: Japanese Industrial Standards Committee Stand
12、ards Board Technical Committee on Ceramics 2003-03-20 .TIS R 621 1-10 : 2003, First English edition published in 2004-01 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN - In the event of any doubts arising as to the contents, the original
13、 JIS is to be the final authority. O JSA 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Prin
14、ted in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 05:26:55 MDTNo reproduction or networking permitted without license from IHS -,-,- R6211-10 : 2003 Contents
15、 Page Introducti on 1 1 Scope 1 2 Normative reference 1 3 Dimensions 1 . . . . 4 Designation 3 Annex (informative) Comparison table between JIS and corresp0ndin.g International Standard 4 . PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee
16、=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 05:26:55 MDTNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD R 6211-10 : 2003 Bonded abrasive products - Dimensions - Part 10: Stones for honing and superfinishings Introduction T
17、his part of JIS R 6211 has been prepared based on the first edition of IS0 603-10 Bonded abrasive products -Dimensions-Part 1 O: Stones for honing and superfinishings published in 1999, with some modifications of the technical contents because of unmatching with an existing law, the structural speci
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 6211 10 2003 R2008 ENG
链接地址:https://www.31doc.com/p-3785632.html