JIS-Z-3131-1976-R2005-ENG.pdf
《JIS-Z-3131-1976-R2005-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-Z-3131-1976-R2005-ENG.pdf(9页珍藏版)》请在三一文库上搜索。
1、JIS z*3131 76 m W L O A 0071,585 7 m UDC 62l.791.053.2:620.172 JIS a I JAPANESE I NDUSTRIAL STANDARD Method of Tension Test for Front Fillet Welded Joint JIS 7 3 I 3 I -1976 Translated and Published by Japanese Standards Association Printed in Japan 5s Copyright Japanese Standards Association Provid
2、ed by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 08:13:16 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S Z*3l13L 76 4933608 007b58b 9 W Translation without guarantee In the event of any doubt arising, the
3、 original standard in Japanese is to be evidence Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 08:13:16 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S Z*3
4、131 76 4933608 0076587 O UDC 621.791.053.2:620.172 JAPANESE INDUSTRLAL STANDARD J I S Method of Tension Test for Front Fillet Welded Joint Z 3131-1976 a 1. Scope This Japanese Industrial Standard specifies the method of the tension test for front fillet welded joint of metallic materials. 2. Typ es
5、of Tests I I The tests shall be of two types of the tension tests for the strapped front llet welded joint and the cross-shaped fillet welded joint. Applicable Standard: JI3 Z 2241-Method of Tension Test for Metallic Materials Copyright Japanese Standards Association Provided by IHS under license wi
6、th JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 08:13:16 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S Z*3L31 76 m 4933688 007b588 2 m 2 Z 3131-1976 3. Test Piece 3.1 The test piece of the strapped front fillet welded joint for
7、use in the tension test shall conform to Figure 1 (No.1 test piece) in the case of finishing the sur- face of welded part and to Figure 2 (No.2 test piece) in the case of using the welded part as it is. The standard dimensions of the test piece and the leg length of fillet shall conform to Table 1.
8、Figure 1. No. 1 Test Piece for Tension Test of Strapped Front Fillet Welded Joint Unit: mm Finishing by Surface finishing machine / / g II A” / / / I I I II / f VI k 100 f ! “iI Y 4 / I f V/ - - - - ,Approx. 200 Approx. 10 a Copyright Japanese Standards Association Provided by IHS under license with
9、 JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 08:13:16 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S ZS313L 76 4933608 0076589 4 , f V Approx. 200 -Approx. 200 3 Z 3131-1976 Leglength f Plate thickness t O Plate thickness T Figu
10、re 2. No.2 Test Piece for Tension Test of Strapped Front Fillet Welded Joint 6 9 12 9 or over 12 or over 16 or over 12 or over 19 or over 25 or over Unit: mm / F I / Table 1 Unit: mm 3.2 The test piece of the cross-shaped illet welded joint for the tension test shall coilform to Figure 3 (No.3 test
11、piece) in the case of finishing the surface of welded part and to Figure 4 (No.4 test piece) in the case of using the welded part as it is. Table 2. The standard dimensions of the test piece and fillet shall conform to , Copyright Japanese Standards Association Provided by IHS under license with JSA
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 3131 1976 R2005 ENG
链接地址:https://www.31doc.com/p-3786326.html