JIS-Z-0403-1-1999-R2004-ENG.pdf
《JIS-Z-0403-1-1999-R2004-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-Z-0403-1-1999-R2004-ENG.pdf(7页珍藏版)》请在三一文库上搜索。
1、J IS JAPANESE IN DUSTRIAL STANDARD Translated and Published by Ja pan ese Standards Association JIS Z 0403-1 11999 Corrugated fibreboard- Part 1 : Determination of flat crush res i st ance ICs 85.060 Descriptors : corrugated, board (paper), compressive strength, compression testing Reference number
2、: JIS Z 0403-1 : 1999 (E) PROTECTED BY COPYRIGHT 4s Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 20:32:59 MSTNo reproduction or networking permitted without license from IHS -,-,- Z 0403
3、-1 1999 Foreword This translation has been made based on the original Japanese Industrial Standard established by the Minister of International Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with the Industrial Standardization Law. By this estab
4、lishment, JIS Z 0401 : 1995 was withdrawn and replaced by JIS Z 0403-1 and JIS Z 0403-2. JIS Z 0403 consists of the following 2 parts under the general title Corrugated fibreboard. Part 1 : Determination of flat crush resistance Part 2 : Determination of edgewise crush resistance Date of Establishme
5、nt: 1999-03-20 Date of Public Notice in Official Gazette: 1999-03-23 Investigated by: Japanese Industrial Standards Committee Divisional Council on Distribution of Goods TIS Z 0403-1 : 1999, First English edition pubIished in 2004-02 Translated and published by: Japanese Standards Association 4-1-24
6、, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electro
7、nic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10
8、/2007 20:32:59 MSTNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS Z 0403-1 : 1999 Corrugated fibreboard- Part 1 : Determination of flat crush resistance Introduction This Japanese Industrial Standard has been prepared based on the second editio
9、n of IS0 3035 Single-faced and single-wall corrugated fibreboard-De- termination of at crush resistance published in 1982 without any modification in the technical contents of the corresponding portions. For items of the flat crush tester, some parts of IS0 3037 Corrugated fibreboard-Determination o
10、f edgewise crush resistance (Unwaxed edge method) are adopted, and items not specified in the corre- sponding International Standards (performance of flat crush tester and test method) are added as the Japanese Industrial Standard. In addition, the portions underlined with dots in this Standard are
11、the matters which are not specified in the corresponding International Standards. 1 Scope This Standard specifies a method for the determination of the flat crush resistance of single-faced and single-wall (double-faced) corrugated fibreboard. In addition, this method is not applicable to double-wal
12、l (double-double-faced) cor- rugated fibreboard and triple-wall (double-double-double-faced) corrugated fibreboard. Remarks : The corresponding International Standards to this Standard are as follows: IS0 3035 : 1982 Single-faced and single-wall corrugated fibreboard- Determination of flat crush res
13、istance IS0 3037 : 1994 Corrugated fibreboard-Determination of edgewise crush resistance (Unwaxed edge method) 2 Normative references The following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. The most recent editions of the standard
14、s shall be applied. JIS P 8110 Paper and board-Sampling for testing Remarks : IS0 186 : 1994 Paper and board-Sampling to determine average quality is equivalent to the said standard. JIS P 8111 Paper, board und pulps-Standard atmosphere for conditioning and testing Remarks : IS0 187 : 1990 Paper, bo
15、ard and pulps-Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples is equivalent to the said standard. 3 Principle Subjection of a test piece of the corrugated fbreboard to an increas- ing force applied perpendicularly to the surfac
16、e by a compression tester having two flat and parallel platens, until the fluting collapses. Measurement of the maximum force sustained by the test piece. PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Win
17、g, Bernie Not for Resale, 03/10/2007 20:32:59 MSTNo reproduction or networking permitted without license from IHS -,-,- 2 Z 0403-1 : 1999 4 Apparatus 4.1 compression tester. Flat crush tester The flat crush tester shall be a motor-driven, platen-type 4.1.1 Compression section The compression section
18、 shall be so constructed that it consists of a pair of parallel platens in the upper and lower sides and at least one side is capable of moving up and down and the surface is flat(1) and robust. The platens shall meet the following requirements: - deviation from parallel not greater than 1 : 1 000;
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 0403 1999 R2004 ENG
链接地址:https://www.31doc.com/p-3786814.html