JIS-C-5401-1-2005-ENG.pdf
《JIS-C-5401-1-2005-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-C-5401-1-2005-ENG.pdf(30页珍藏版)》请在三一文库上搜索。
1、JIS JAPANESE I N DUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS C 5401-1 Connectors for electronic equipment - Part 1 : Generic specification ICs 31.220.10 Reference number : JIS C 5401-1 : 2005 (E) PROTECTED BY COPYRIGHT 16 S Copyright Japanese Standards Associatio
2、n Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 22:22:47 MDTNo reproduction or networking permitted without license from IHS -,-,- C 5401-1 : 2005 (IEC 61076-1 1995) Foreword This translation has been made based on the original
3、Japanese Industrial Standard established by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal of establishing a Japanese Industrial Standard from Japan Electronics and Information Technology Industries Associati
4、on (JEITA), with a draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law. This Standard has been made based on IEC 61076-1:1995 Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high speed data applications -
5、Part 1: Generic specification for the purposes of making it easier to compare this Standard with International Standard; to prepare Japanese Industrial Standard conforming with International Standard; and to propose a draft of an International Standard which is based on Japanese Industrial Standard.
6、 Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties. The releva
7、nt Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical prope
8、rties. JIS C 5401 series consists of the following 7 parts under the general title ? Con nec tors for e 1 ec t ro n i c eq u ip m e n t ? : Part 1: Generic specification Part 2: Circular connectors with assessed quality - Sectional specification Part 2-001: Circular connectors with assessed quality
9、- Sectional specification B 1 a n k Detail Spec i f ica t i o n Part 3: Rectangular connectors with assessed quality - Sectional specification Part 3-001: Rectangular connectors with assessed quality - Blank Detail Spec i f i c a t i o n Part 4: Printed board connectors with assessed quality - Secti
10、onal Part 4-001: Printed Board Connectors with assessed quality - Blank Detail Specification specification Date of Establishment: 2005-03-20 Date of Public Notice in Official Gazette: 2005-03-22 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Electroni
11、cs Technology JIS C 5401-1 :2005, First English edition published in 2005-07 Translated and published by: Japanese Standards Association 4-1-24, Altasaka, Minato-ltu, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 200
12、5 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utiliLcd in any form or by any mcans, clcctronic or mcchanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyrigh
13、t Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 22:22:47 MDTNo reproduction or networking permitted without license from IHS -,-,- C 5401-1 : 2005 (IEC 61076-1 : 1995) Contents Page Introduction .
14、1 General information 1.1 Scope 1.2 General considerations relating to specifications 1.3 Normative references 2 Technical information . 2.1 Terminology 2.2 Classification into climatic categories . 2.3 Creepage and clearance distances 2.4 Current-carrying capacity 2.5 JIS type designation . 2.6 Mar
15、king . 2.7 Dimensional information 3 Quality assessment procedures 3.1 Quality assessment definitions . 3.2 Approval of manufacturers, independent test laboratories, 1 1 1 1 3 5 5 5 6 6 6 6 7 8 8 . and distributors 11 3.3 Qualification approval (QA) 12 3.5 Quality conformance inspection 20 Qualifica
16、tion approval / quality assessment systems . 23 . . 3.4 Capability approval (CA) 13 3.6 4 Tests and test schedules 23 4.1 General aspects 23 4.2 Test schedules 24 4.3 Grouping tests 24 4.4 Delayed delivery 25 4.5 4.6 Delivery of tested connectors 25 Annex A (normative) Common lettering system to be
17、used in drawing- 26 Release for delivery, before completion of “Group B” tests . 25 (i PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/13/2007 22:22:47 MDTNo reproduction or
18、networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS C 5401-1 2005 (IEC 61076-1 : 1995) Connectors for electronic equipment - Part 1: Generic specification Introduction This Japanese Industrial Standard has been prepared based on the first edition of IEC 61076-1 Conne
19、ctors with assessed quality, for use in d.c., low frequency analogue and in digital high speed data applications - Part 1: Generic specification published in 1995 and Amendment 1 (1996) and Amendment 2 (2001) without modifying the technical contents of the original International Standard. In this ca
20、se edition 1:1995 is consolidated with amendments 1:1996 and 2:2001. The portion given dotted underlines is the matter not stated in the original International Standard. 1 General information 1.1 Scope This part of JIS C 5401 establishes uniform specifications, testing requirements and quality asses
21、sment procedures for connectors. This generic specification is applicable to a family of connectors for use in electronic and electrical equipment. Connectors designed for use at radio frequencies are not covered. The quality assessment procedures are divided into qualification approval (QA) and cap
22、ability approval (CA) procedures, of which quality conformance inspection forms a part. NOTE : The International Standard(s) corresponding to this Standard is/are as follows. In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard an
23、d JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ IEC Guide 21. IEC 61076-1:1995 Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high speed data applications - Part i: Generic specification and Amendment 1 (1996) and Amendm
24、ent 2 (2001) (IDT) 1.2 General considerations relating to specifications This generic specification contains, or gives reference to, the terms, definitions, symbols, test methods and information relating to the inspection peculiar to connectors, and it also includes test sequences for quality assess
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 5401 2005 ENG
链接地址:https://www.31doc.com/p-3786942.html