NAVISTAR-CEMS-G-5-PART-II-2008.pdf
《NAVISTAR-CEMS-G-5-PART-II-2008.pdf》由会员分享,可在线阅读,更多相关《NAVISTAR-CEMS-G-5-PART-II-2008.pdf(4页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL TRUCK AND ENGINE CORPORATION CEMS (CORPORATE ENGINEERING MATERIAL SPECIFICATION) NUMBER: CEMS G-5, Part II General TITLE: Part II Paints - Topcoats, General Requirements CURRENT ISSUE DATE: February 2008 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPE
2、RSEDES ISSUE OF: December 2004 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible
3、 to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Added section 2.2 on Restricted Chemical Substances; editorial changes. 1.0 SCOPE The intent of this specification is to establish acceptable durability and qualit
4、y levels for the finish on International products and to define requirements and physical properties of the various materials used in the painting operation. 2.0 INTRODUCTION This specification is divided into eight parts as follows: Part I, Section A - Product Finishing Requirements Part V - Primer
5、s Part I, Section B - Paint Material Requirements Part VI - Paints for Repair Tel. No. 1-800-854-7179. 8.1.1 Color Color numbers and gloss shall be in accordance with CEMS G-5, Part I, Section B, unless otherwise directed. FEBRUARY 2008 Page 2 of 4 NUMBER: TITLE: Part II Paints - Topcoats, CURRENT I
6、SSUE DATE: CEMS G-5, PART II General Requirements February 2008 This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Inter
7、national Truck and Engine Corporation. Color Approvals, Send Materials To: Color Standard Requests/Support Contact: International Truck and Engine Corporation Truck Development and Technology Center Non-Metals Engineering Laboratory 2911 Meyer Road Fort Wayne, In 46803 Akzo Nobel Coatings Inc. 1845
8、Maxwell Street Troy, MI 48084 Attn: Color Services Phone (866) 817-5053 E-mail 8.2 ASTM Test Methods ASTM test methods are available from ASTM, 1916 Race Street, Philadelphia, Pa. 19103 8.3 Federal Test Methods Federal test Methods are available from the, Business Service Center, General Services A
9、dministration, Washington, D.C. 20407 8.4 SAE Standards and Test Methods SAE standards are available from; Society of Automotive Engineers; 400 Commonwealth Drive; Warrendale, Pa. 15096 9.0 SOURCE APPROVAL AND QUALITY CONTROL 9.1 Supplier Requirements All suppliers to International Truck and Engine
10、are required to be registered to ISO 9001 Quality System Requirements. International will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification w
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVISTAR CEMS PART II 2008
链接地址:https://www.31doc.com/p-3788695.html