JIS-R-6211-13-2003-R2008-ENG.pdf
《JIS-R-6211-13-2003-R2008-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-R-6211-13-2003-R2008-ENG.pdf(11页珍藏版)》请在三一文库上搜索。
1、JIS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS R 6211-13:2003 Bonded abrasive products - Dimensions - Part 13 : Grinding wheels for deburring and fettling on a vertical grinder ICs 25.100.70 Reference number : JIS R 6211-13 : 2003 (E) PROTECTED BY COP
2、YRIGHT 7s Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:49:12 MDTNo reproduction or networking permitted without license from IHS -,-,- R 6211-13 : 2003 Foreword This translation has bee
3、n made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with the proposal of revising a Japanese Industrial Stan- dard from the Japan Grinding Wheel Association
4、 (GIS)/the Japanese Standards Association (JSA), with a draft of Industrial Standard based on the provision of Article 12 Clause 1 of the Industrial Standardization Law which shall be applied by Article 14 of the same Law. Conse- quently JIS R 6211-13:1999 is replaced with JIS R 6211-132003. In this
5、 revision, IS0 603-13:1999 Bonded abrasive products-Dimensions- Part 13:Grinding wheels far deburring and fettling on a vertical grinder is used as a basis to make Japanese Industrial Standard to conform to the corresponding International Standard. Attention is drawn to the possibility that some par
6、ts of this Standard, which have technical properties, may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public. The Minister of Economy, Trade and Industry and the Japanese
7、 Industrial Standards Commit- tee are not responsible for identeing the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical properties. JIS R 6211 consists o
8、f the following 16 parts under the general title Bonded abrasive products- Dimensions. Part 1 : Grinding wheels for external cylindrical grinding between centres Part 2 : Grinding wheels for centerless external cylindrical grinding Part 3 : Grinding wheels for internal cylindrical grinding Part 4 :
9、Grinding wheels for surface grindinglperipheral grinding Part 5 : Grinding wheels for surface grinding/face grinding Part 6 : Grinding wheels for tool and tool room grinding Part 7 : Grinding wheels for manually guided grinding Part 8 : Grinding wheels for deburring and fettlingsnagging Part 9 : Gri
10、nding wheels for high-pressure grinding Part 10 : Stones for honing and superfmshings Part 11 : Hand finishing sticks Part 12 : Grinding wheels for deburring and fettling on a straight grinder Part 13 : Grinding wheels for deburring and fettling on a vertical grinder Part 14 : Grinding wheels for de
11、burring and fettling/snagging on an angle grinder Part 15 : Grinding wheels for cutting-offon stationary or mobile cutting-offmachines Part 16 : Grinding wheels for cutting-off on hand held power tools Date of Establishment: 1999-02-20 Date of Revision: 2003-03-20 Date of Public Notice in Official G
12、azette: 2003-03-20 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Ceramics JIS R 621 1-13 : 2003, First English edition published in 2004-01 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN
13、In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2004 Ali rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying an
14、d microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:49:12 MDTNo reproduction or networkin
15、g permitted without license from IHS -,-,- R 6211-13 : 2003 Contents Page (i PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:49:12 MDTNo reproduction or networking p
16、ermitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS R 6211-13 : 2003 Bonded abrasive products - Dimensions - Part 13 : Grinding wheels for deburring and fettling on a vertical grinder Introduction This part of JIS R 6211 has been prepared based on the first edition of IS0 603-13
17、 Bonded abrasive products -Dimensions -Part 13: Grinding wheels for debur- ring and fettling on an vertical grinder published in 1999, with modifying the technical contents of the tables in A series because of unmatching with an existing law, the struc- tural specification for grinding machine speci
18、fied in Industrial Safety and Health Law. The tables in B series specify the dimensions mainly used in Japanese market. However, A series shall take precedence, and B series will be restudied in five years. The portions given sidelines or underlines with dots in this part of JIS R 6211 are the matte
19、rs not included in the original International Standard. 1 for deburring and fettling on a vertical grinder of - Type 6 : - Type 35 : - Type 36 : Scope This part of JIS R 6211 specifies the nominal dimensions of grinding wheels Straight cup wheel Cemented or clamped disc wheel Disc wheel with inserte
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 6211 13 2003 R2008 ENG
链接地址:https://www.31doc.com/p-3788700.html