JIS-Z-3265-1998-R2004-ENG.pdf
《JIS-Z-3265-1998-R2004-ENG.pdf》由会员分享,可在线阅读,更多相关《JIS-Z-3265-1998-R2004-ENG.pdf(6页珍藏版)》请在三一文库上搜索。
1、c 1 STDmJIS Z 3265-ENGL 1998 H 4933608 0560739 515 W J IS JAPANESE INDUSTRIAL STANDARD Translated and Published by Ja pa nese Stand a rds Associati on Nickel brazing filler metals ICs 25.160.50 Descriptors : nickel alloys, brazing alloys, filler metal, nickel Reference number : JE3 Z 3265 : 1998 (E)
2、 4 s STDsJIS 2 3265-ENGL 1998 m 4933608 O560720 i 2 3 7 Z 3265 : 1998 Foreword This translation has been made based on the original Japanese Industrial Standard revised by the Minister of International Trade and Industry through deliberations at Japanese Industrial Standards Committee in accordance
3、with the Industrial Standardization Law. Consequently JIS Z 3265 : 1986 is replaced with JIS Z 3265 : 1998. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or applicatio
4、n for registration of utility model after opening to the public which have technical properties. The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or ap
5、plication for registration of utility model after opening to the public which have the said technical properties. Date of Establishment: 1968-05-01 Date of Revision: 1998-05-20 Date of Public Notice in Official Gazette: 1998-05-20 Investigated by: Japanese Industrial Standards Committee Divisional C
6、ouncil on Welding JIS Z 3265 : 1998, First English edition published in 2000-01 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. i . L O
7、JSA 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan ! ? I/ JAPANESE INDUSTRI
8、AL STANDARD Nickel brazing filler metals JIS Z 3265: 1998 Introduction This Japanese Industrial Standard is the revised version of JIS Z 3265: 1986 Nickel brazing filler metals, after taking the contents of the second edition of IS0 3677 Filler metal for soft soldering, brazing and braze welding-Des
9、ignation issued in 1992 into account. In addition to the items specified in the JI$, “Designation and Symbols” specified in IS0 3677 are adopted and coordinat- ed without changing the technical contents. 1 Scope brazing, hereafter referred to as “brazing filler metals”. This Japanese Industrial Stan
10、dard specifies the nickel brazing filler metals used for 2 Normative reference The following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. The most recent editions of the standards indicated below shall be applied. JIS H 0321 JIS Z 39
11、05 General rules for inspection of non-ferrous metal materials Methods for chemical analysis of nickel brazing filler metals 3 Classification chemical composition as shown in Table 1. The brazing filler metals shall be classified into 8 classes on the basis of their 4 Quality The quality of the braz
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- JIS 3265 1998 R2004 ENG
链接地址:https://www.31doc.com/p-3789566.html