MIL-DTL-3922-61D-2000 1.08.pdf
《MIL-DTL-3922-61D-2000 1.08.pdf》由会员分享,可在线阅读,更多相关《MIL-DTL-3922-61D-2000 1.08.pdf(5页珍藏版)》请在三一文库上搜索。
1、 MIL-DTL-3922/61D 6 March 2000 SUPERSEDING MIL-F-3922/61C 7 October 1982 DETAIL SPECIFICATION SHEET FLANGES, WAVEGUIDE (CHOKE) (ROUND, 8 HOLE) This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring the flanges described h
2、erein shall consist of this document and the latest issue of MIL-DTL-3922. FIGURE 1. Flange configurations. AMSC N/A 1 of 5 FSC 5985 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND MIL-DTL-3922/61D 2 NOTES:Inches mm 1. Dimensions are in inches002 0.05 2.
3、Metric equivalents are in parentheses003 0.08 3. Metric equivalents are given for general information only and are based.005 0.13 upon 1.00 inch = 25.4 mm006 0.15 4. Roughness of mating surfaces, including seal groove, shall not exceed 63 microinches.010 0.25 in accordance with ASME B46.1, except th
4、at flaws shall be included in the roughness.015 0.38 height measurement125 3.18 .250 6.35 FIGURE 1. Flange configurations - Continued. MIL-DTL-3922/61D 3 TABLE I. Dash numbers and dimensions. PIN M3922/61-Dimensions DashUsed withABCDEF no.Waveguide M85/1- Mating flange M3922/56- .006 (0.15) .006 (0.
5、15) .015 (0.38) BSCMax R 001 1/0410022.840 (72.14) 1.340 (34.04) 5.313 (134.95) 4.750 (120.65) .046 (1.17) .250-20 UNC-2B 002 2/043001“ 003 1/041002“ 004 2/043001“ Dimensions Dash no. G .015 (0.38) H .015 (0.38) J .015 (0.38) K .015 (0.38) L .003 (0.08) M .004 (0.10) N .005 (0.13) P .015 (0.38) 001
6、1/4.188 (106.38) .313 (7.95) 1.250 (31.75) 3.500 (88.90) 3.002 (76.25) .250 (6.35) 3.320 (84.33) 1.000 (25.40) 002 2/“3.002 (76.25) “ 003 1/“3.006 (76.35) “ 004 2/“3.006 (76.35) “ Dimensions Dash no. Q .001 (0.03) R .005 (0.13) S .005 (0.13) T .005 (0.13) U .005 (0.13) V .015 (0.38) W .015 (0.38) Y
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- MIL-DTL-3922-61D-2000 1.08 MIL DTL 3922 61 2000
链接地址:https://www.31doc.com/p-3789696.html