MSS-SP-25-2008.pdf
《MSS-SP-25-2008.pdf》由会员分享,可在线阅读,更多相关《MSS-SP-25-2008.pdf(27页珍藏版)》请在三一文库上搜索。
1、 MSS SP-25-2008 Standard Practice Developed and Approved by the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 127 Park Street, NE Vienna, Virginia 22180 Phone: (703) 281-6613 Fax: (703) 281-6671 E-mail: infomss-hq.org www.mss-hq.org Standard Marking System for Valves
2、, Fittings, Flanges, and Unions -,-,- MSS STANDARD PRACTICE SP-25 i This MSS Standard Practice was developed under the consensus of the MSS Technical Committee 302 and the MSS Coordinating Committee. The content of this Standard Practice is the result of the efforts of competent and concerned volunt
3、eers to provide an effective, clear, and non-exclusive specification that will benefit the industry as a whole. This MSS Standard Practice is intended as a basis for common practice by the manufacturer, the user, and the general public. The existence of an MSS Standard Practice does not in itself pr
4、eclude the manufacture, sale, or use of products not conforming to the Standard Practice. Mandatory conformance is established only by reference in a code, specification, sales contract, or public law, as applicable. Unless otherwise specifically noted in this MSS SP, any standard referred to herein
5、 is identified by the date of issue that was applicable to the referenced standard(s) at the date of issue of this MSS SP (See Annex A). U.S. customary units in this Standard Practice are the standard; the metric units are for reference only. Substantive changes in this 2008 edition are “flagged” by
6、 parallel bars as shown on the margins of this paragraph. The specific details of the changes may be determined by comparing the material flagged with that in the previous edition. Any part of this Standard Practice may be quoted. Credit lines should read Extracted from MSS SP-25, 2008 with permissi
7、on of the publisher, the Manufacturers Standardization Society. Reproduction prohibited under copyright convention unless written permission is granted by the Manufacturers Standardization Society of the Valve and Fittings Industry Inc. Originally Approved July, 1934 Copyright , 2008 by Manufacturer
8、s Standardization Society of the Valve and Fittings Industry, Inc. Printed in U.S.A. MSS STANDARD PRACTICE SP-25 ii FOREWORD The initial issue of the Standard Marking System was made by the Manufacturers Standardization Society in 1934. It stated the basic rules but was considered to need more detai
9、ls for general use. A second edition was therefore prepared with additional details and examples and was published in 1936. The third edition, in 1954, recognized the use of new materials, increased operating temperatures and pressures and added more examples of markings for regular products. In 195
10、8, the fourth edition incorporated relatively minor changes and updates and included some additional examples. The format was revised for the fifth edition in 1960. It permitted the use of nameplates on valve bodies, and added requirements for making ductile iron products. The sixth edition in 1964
11、broadened the scope of the Marking Standard Practice and revised the examples and sections of the text to reflect changes in piping requirements. The seventh edition in 1978 was completely revised and rewritten to simplify its cross references and to improve its readability. It also incorporated the
12、 marking features of pressure-temperature marking designations contained in American National Standards on products and materials. It was rearranged so that the General Rules were stated in Sections 1 to 11. These were amplified in Sections 12 to 18 which gave specific rules and examples of marking
13、requirements for various products and materials. In 1993, the eighth edition incorporated relatively minor changes and updates. The 1998 ninth edition includes minor revisions required per current MSS practices. This 2008 tenth edition includes revisions to the ASME B16.34 example marking and mandat
14、ory MSS conformance marking and clarifies general requirements. -,-,- MSS STANDARD PRACTICE SP-25 iii TABLE OF CONTENTS SECTION PAGE GENERAL RULES 1 SCOPE. 1 2 GENERAL MARKING REQUIREMENTS. 1 3 MANUFACTURERS NAME OR TRADEMARK . 1 4 RATING DESIGNATION 1 5 MATERIAL DESIGNATION. 2 6 MELT IDENTIFICATION
15、 3 7 VALVE TRIM IDENTIFICATION 3 8 SIZE DESIGNATION. 4 9 IDENTIFICATION OF THREADED ENDS 5 10 RING-JOINT FACING IDENTIFICAITON. 6 11 PERMISSIBLE OMISSION OF MARKINGS . 6 SPECIFIC RULES 12 MARKING REQUIREMENTS FOR FLANGES, FLANGED FITTINGS, AND FLANGED UNIONS 6 13 MARKING REQUIREMENTS FOR THREADED FI
16、TTINGS AND UNION NUTS . 9 14 MARKING REQUIREMENTS FOR WELDING AND SOLDER JOINT FITTINGS AND UNIONS. 12 15 MARKING REQUIREMENTS FOR NON-FERROUS VALVES 13 16 MARKING REQUIREMENTS FOR GRAY IRON VALVES 14 17 MARKING REQUIREMENTS FOR DUCTILE IRON VALVES 14 18 MARKING REQUIREMENTS FOR STEEL VALVES 15 TABL
17、E 1 Common Symbols for Metallic Materials 3 2 Common Symbols for Non-Metallic Materials . 4 3 Size Identification Nominal Diameter 5 4 Examples of Threaded Type Symbols. 6 5 ASME B16.1 Rating Markings 7 ANNEX A Referenced Standards and Applicable Dates 21 -,-,- MSS STANDARD PRACTICE SP-25 1 STANDARD
18、 MARKING SYSTEM FOR VALVES, FITTINGS, FLANGES, AND UNIONS 1. SCOPE 1.1 This marking system applies to valves, fittings, flanges, and unions used in piping connections which include (but are not limited to) flanged, soldered, brazed, threaded, or welded joints. 1.2 These specified markings serve to i
19、dentify the manufacturer, the rating designation, materials of construction and special service limitations imposed by the manufacturer. They are used for product identification and to assist in proper application. 2. GENERAL MARKING REQUIREMENTS 2.1 Each product of a size and shape permitting legib
20、le marking shall be marked in accordance with the provisions of this Standard Practice. 2.2 Markings shall be applied to the body of valves, fittings and the nut of unions or on an identification plate. For quarter turn valves, markings shall be applied to the body, identification plate, or handle.
21、Markings on covered quarter turn valve handles may not be integral with the base handle material. 2.3 Markings shall consist of numerals, letters, or symbols cast, forged, stamped, or otherwise made integral with the product; or markings on an identification plate attached to the product; or both. W
22、here stamping is used on pressure containing walls, low stress stamps which produce a round bottom impression shall be used; such low stress stamps are not required on flanged edges or on raised pads provided for marking purposes. 2.4 Unless otherwise prohibited, markings obliterated during manufact
23、uring of steel products may be replaced by weld deposition, welded plates, or stamping. 2.5 Markings indicating conformance with recognized documents, such as the ASME Boiler Pressure Vessel Codes, API, Factory Mutual, and Underwriters Laboratories may be applied only by authorized, licensed, or app
24、roved manufacturers. Such markings shall be applied only to products fully conforming to the code qualification requirements and may be shown on the body or an attached plate, at the option of the manufacturer. 2.6 Manufacturers may apply markings indicating conformance with codes and standards such
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- MSS SP 25 2008
链接地址:https://www.31doc.com/p-3790484.html