NF-EN-10204-2005-ENG.pdf
《NF-EN-10204-2005-ENG.pdf》由会员分享,可在线阅读,更多相关《NF-EN-10204-2005-ENG.pdf(13页珍藏版)》请在三一文库上搜索。
1、NF EN 10204 janvier 2005 Ce document est usage exclusif et non collectif des clients Saga Web. Toute mise en rseau, reproduction et rediffusion, sous quelque forme que ce soit, mme partielle, sont strictement interdites. This document is intended for the exclusive and non collective use of Saga Web
2、customers. All network exploitation, reproduction and re-dissemination,even partial, whatever the form (hardcopy or other media), is strictly prohibited. Saga Web Pour THALES CORPORATE SERVICES SAS - EPM Client 04988312 le 16/7/2009 10:00 AFNOR 2005AFNOR 20051st issue 2005-01-P AFNOR 2005 All rights
3、 reserved FE111300ISSN 0335-3931 NF EN 10204 January 2005 Classification index: A 00-001 European standard French standard Published and distributed by Association Franaise de Normalisation (AFNOR French standard institute) 11, avenue Francis de Pressens 93571 Saint-Denis La Plaine Cedex Tel.: + 33
4、(0)1 41 62 80 00 Fax: + 33 (0)1 49 17 90 00 www.afnor.fr ICS: 77.140.01 Metallic products Types of inspection documents F : Produits mtalliques Types de documents de contrle D : Metallische Erzeugnisse Arten von Prfbescheinigungen French standard approved by decision of the Director General of AFNOR
5、 on December 20, 2004, taking effect on January 20, 2005. Replaces the approved standard NF EN 10204 dated December 1991 and its amendment A1 dated December 1997. CorrespondenceThe European standard EN 10204:2004 has the status of French standard. AnalysisThis document specifies different types of i
6、nspection documents supplied to the buyer in conformity with the regulations of the order for the delivery of all metallic products. DescriptorsTechnical International Thesaurus: iron-and steel products, steels, documents, inspection, tests, acceptance certificates. ModificationsWith respect to the
7、replaced documents, this document only comprises four types of inspection documents (types 2.1, 2.2, 3.1 and 3.2) and a ZA Annex has been added in view to manage the relationship with Directive 97/23/CE. Corrections EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10204 October 2004 ICS 01.110;
8、77.080.01; 77.120.01 Supersedes EN 10204:1991 English version Metallic products - Types of inspection documents Produits mtalliques - Types de documents de contrle Metallische Erzeugnisse - Arten von Prfbescheinigungen This European Standard was approved by CEN on 8 August 2004. CEN members are boun
9、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Ce
10、ntral Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status a
11、s the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, S
12、pain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nation
13、al Members. Ref. No. EN 10204:2004: E EN 10204:2004 (E) 2 Contents page Foreword3 1 Scope 4 2 Terms and definitions .4 3 Inspection documents based on non-specific inspection 4 4 Inspection documents based on specific inspection5 5 Validation and transmission of inspection documents.5 6 Transmission
14、 of inspection documents by an intermediary 6 Annex A (informative) Summary of inspection documents.7 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC8 Bibliography10 EN 10204:2004 (E) 3 Foreword This document (EN 10204:2004)
15、has been prepared by Technical Committee ECISS/TC 9 “Technical conditions of delivery and quality control”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by
16、 April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. This document supersedes EN 10204:1991. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements
17、 of EU Directives 97/23/EC. For relationship with EU Directive 97/23/EC, see informative Annex ZA, which is an integral part of this document. The main changes are: new definitions: “manufacturer” , “intermediary”, “product specification”; reduction of the number of inspection documents: type 2.3 of
18、 the previous edition has been deleted; type 3.1 replaces type 3.1.B of the previous edition; type 3.2 replaces types 3.1.A, 3.1. C and the inspection report 3.2 of the previous edition. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countrie
19、s are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
20、 and United Kingdom. EN 10204:2004 (E) 4 1 Scope 1.1 This document specifies the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of all metallic products e.g. plates, sheets, bars, forgings, castings, whatever thei
21、r method of production. 1.2 This document may also apply to non-metallic products. 1.3 This document is used in conjunction with the product specifications which specify the technical delivery conditions of the products. NOTE 1 The list of information that may be included in the inspection documents
22、 can be found in appropriate documents, e.g. EN 10168 for steel. NOTE 2 Annex A gives a summary of the different inspection documents. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 non-specific inspection inspection carried out by the manuf
23、acturer in accordance with his own procedures to assess whether products defined by the same product specification and made by the same manufacturing process, are in compliance with the requirements of the order or not. The products inspected are not necessarily the products actually supplied 2.2 sp
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NF EN 10204 2005 ENG
链接地址:https://www.31doc.com/p-3790527.html