《NACE-MR-0175-2003.pdf》由会员分享,可在线阅读,更多相关《NACE-MR-0175-2003.pdf(175页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD NACE MROl75/ISO 151 56-1 :2001 TECHNICAL CORRIGENDUM 1 Published 2005-09-01 Item No. 21307 B N T E R N A T 3 O N A I_ INTERNATIONAL ORGANIZATION FOR STANDARDIZATION MWYHAPOflHA OPrAHU3AU no CTAHflAPTUSWUU ORGANISATION INTERNATIONALE DE NORMALISATION Petroleum and natural gas i
2、ndustries - Materials for use in H2S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials TECHNICAL CORRIGENDUM 1 Technical Corrigendum 1 to IS0 151 56-1 was prepared by Technical Committee ISO/TC 67, Materials, equipment and of
3、fshore structures for petroleum, petrochemical and natural gas industries. ICs 75.1 80.01 Ref. No. NACE MROl75ASO 15156- 1 :2001/Cor.l:2005(E) ISBN 1-57590-021 -1 O NACE InternationalllSO 2005 -All rights reserved Published in the U.S.A. by NACE NACE MROl75/ISO 15156-1:2001/Cor.l:2005(E) Page 2, Tab
4、le 1 - List of equipment: Replace Table 1 with the following: Table 1 - List of equipment NACE MR0175iiSO 15156-1 is applicable to materials used for the following equipment )rilling, well construction and well-servicing equipment Vells, including subsurface equipment, gas lift equipment, wellheads
5、and Christmas trees lowlines, gathering lines, field facilities and field wocessing plants Vater-handling equipment datura1 gas treatment plants -ransportation pipelines for liquids, gases and multiphase luids or all equipment above Permitted exclusions Equipment only exposed to drilling fluids of c
6、ontrolled compositiona Drill bits Blowout Preventer (BOP) shear bladesb Drilling riser systems Work strings Wireline and wireline equipmentc Surface and intermediate casing Sucker rod pumps and sucker rodsd Electric submersible pumps Other artificial lift equipment Slips Crude oil storage and handli
7、ng facilities operating at a total absolute pressure below 0.45 MPa (65 psi) Water-handling facilities operating at a total absolute pressure below 0.45 MPa (65 psi) Water injection and water disposal equipmente Lines handling gas prepared for general commercial and domestic use Components loaded on
8、ly in compression See NACE MR0175/ISO 151 56-2:2003, A.2.3.2.3 for more information. See NACE MR0175/ISO 15156-2:2003, A.2.3.2.1 for more information. Wireline lubricators and lubricator connecting devices are not permitted exclusions. For sucker rod pumps and sucker rods, reference can be made to N
9、ACE Standard MRO176. For water injection and water disposal, reference can be made to NACE Standard RP0475. Page 1 O, Bibliography: Add the following: 7 NACE Standard RP0475, Selection of Metallic Materials to Be Used in All Phases of Water Handling for Injection into Oil-Bearing Formations 2 O NACE
10、 InternationalllSO 2005 -All rights reserved INTERNATIONAL STANDARD NACE MROl75/ISO 151 56-2:2003 TECHNICAL CORRIGENDUM 1 Published 2005-09-01 Item No. 21307 1 N T E R N A T I O N W L INTERNATIONAL ORGANIZATION FOR STANDARDIZATION MWYHAPOflHA OPrAHU3AU no CTAHflAPTUSWUU ORGANISATION INTERNATIONALE D
11、E NORMALISATION Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons TECHNICAL CORRIGENDUM 1 Technical Corrigendum 1 to NACE MROl75/ISO 15156-2 was prepare
12、d by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries. ICs 75.1 80.01 Ref. No. NACE MROl75ASO 15156- 2: 2003/Cor.l: 2005( E) ISBN 1-57590-021 -1 O NACE InternationalhSO 2005 -All rights reserved Published in the U.S.A
13、. by NACE NACE MROl75/ISO 151 56-2:2003/Cor.l:2005(E) Page 2, Table 1 - List of equipment: Replace Table 1 with the following: Table 1 - List of equipment NACE MR0175iiSO 15156-2 is applicable to materials used for the following equipment )rilling, well construction and well-servicing equipment Vell
14、s, including subsurface equipment, gas lift equipment, wellheads and Christmas trees lowlines, gathering lines, field facilities and field wocessing plants Vater-handling equipment datura1 gas treatment plants -ransportation pipelines for liquids, gases and multiphase luids or all equipment above Pe
15、rmitted exclusions Equipment only exposed to drilling fluids of controlled compositiona Drill bits Blowout Preventer (BOP) shear bladesb Drilling riser systems Work strings Wireline and wireline equipmentc Surface and intermediate casing Sucker rod pumps and sucker rodsd Electric submersible pumps O
16、ther artificial lift equipment Slips Crude oil storage and handling facilities operating at a total absolute pressure below 0.45 MPa (65 psi) Water-handling facilities operating at a total absolute pressure below 0.45 MPa (65 psi) Water injection and water disposal equipmente Lines handling gas prep
17、ared for general commercial and domestic use Components loaded only in compression See A.2.3.2.3 for more information. See A.2.3.2.1 for more information. Wireline lubricators and lubricator connecting devices are not permitted exclusions. For sucker rod pumps and sucker rods, reference can be made
18、to NACE Standard MRO176. For water injection and water disposal, reference can be made to NACE Standard RP0475. Page 2, Clause 2, Normative references: Add the following reference after NACE MROl75ASO 151 56-1 :2001: NACE MROl75/ISO 151 56-3:2003, Petroleum and natural gas industries - Materials for
19、 use in HS- containing environments in oil and gas production - Pari 3: Cracking-resistant CAs (corrosion-resistant alloys) and other alloys 2 O NACE InternationalllSO 2005 -All rights reserved NACE MROl75ASO 151 56-2:2003/Cor.l:2005(E) Page 3, 3.1 : Replace 3.1 with the following: 3.1 Brinell hardn
20、ess HBW hardness value, measured in accordance with IS0 6506-1, normally using a 10-mm diameter tungsten carbide ball and a force of 29.42 kN NOTE For the purposes of this provision, ASTM E 10 is equivalent to IS0 6506-1. Page 5, 3.16: Replace 3.1 6 with the following: 3.1 6 Rockwell C hardness HRC
21、hardness value, measured in accordance with IS0 6508-1, obtained using a diamond cone indenter and a force of 1.471 N NOTE For the purposes of this provision, ASTM E 18 is equivalent to IS0 6508-1 Page 5, 3.23: Replace 3.23 with the following: 3.23 Vickers hardness HV hardness value, measured in acc
22、ordance with IS0 6507-1, obtained using a diamond pyramid indenter and one of a variety of possible applied loads NOTE For the purposes of this provision, ASTM E 92 is equivalent to IS0 6507-1. Page 11, 7.3.3.2 Hardness testing methods for welding procedure qualification: Replace 7.3.3.2 with the fo
23、llowing: Hardness testing for welding procedure qualification shall normally be carried out using the Vickers HV 10 or HV 5 method in accordance with IS0 6507-1, or the Rockwell method in accordance with IS0 6508-1 or ASTM E 18 using the 15N scale. NOTE For the purposes of this provision, ASTM E 92
24、is equivalent to IS0 6507-1 and ASTM E 18 is equivalent to IS0 6508-1. The HRC method may be used for welding procedure qualification if the design stress does not exceed two- thirds of SMYS and the welding procedure specification includes post weld heat treatment. The use of the HRC method for weld
25、ing procedure qualification in all other cases shall require the agreement of the equipment user. NOTE Hardness surveys using the Vickers or Rockwell 15N testing method produce a more detailed picture of weld hardness and its variations. Hardness surveys using the HRC testing method might not detect
26、 small zones in welds or HAZs where the hardness exceeds the acceptance criteria for the Vickers or Rockwell 15N testing method. The significance of such small hard zones is not well understood. The use of other hardness testing methods shall require the agreement of the equipment user. The Vickers
27、or Rockwell 15N hardness testing method shall be used for the qualification of alternative weld hardness acceptance criteria as permitted in 7.3.3.4. O NACE InternationalllSO 2005 -All rights reserved 3 NACE MROl75/ISO 151 56-2:2003/Cor.l:2005(E) Page 1 1, 7 . 3 . 3 . 3 Hardness surveys for welding
28、procedure qualification: Replace 7.3.3.3 with the following: Vickers hardness surveys shall be in accordance with Figure 2 for butt welds, Figure 3 for fillet welds and Figure4 for repair and partial penetration welds. HRC surveys of butt welds shall be in accordance with Figure 5. Survey requiremen
29、ts for other joint configurations shall be developed from these figures. Hardness surveys for qualification of overlay welding procedures shall be in accordance with Figure 6. Page 15, 7 . 3 . 3 . 3 Hardness surveys for welding procedure qualification: Add the following Figure 6. Dimensions in milli
30、metres B B B A B C weld heat affected zone (visible after etching) lines of hardness survey indentations 1 to 12 _ layer of weld overlay (visible after etching) a Using the Vickers or Rockwell 15N measurement methods, hardness impressions 2, 6 and 10 should be entirely within the heat-affected zone
31、and located as close as possible to, but no more than 1 mm from, the fusion boundary between the weld overlay and HAZ. The Rockwell C hardness measurement method may be used subject to the requirements of 7.3.3.2. HRC hardness impressions in the HAZ shall be located within 2 mm of the fusion boundar
32、y Figure 6 -Weld overlay Page 18, A.2.1.4 Welding: Replace A.2.1.4 with the following: Welding and weld hardness determinations shall be performed in accordance with 7.3.3. Acceptable maximum hardness values for carbon steel, carbon manganese steel and low alloy steel welds are given in Table A.l. 4
33、 O NACE InternationalllSO 2005 -All rights reserved NACE MROl75ASO 151 56-2:2003/Cor.l:2005(E) Vickers HV 10 or HV 5 or Rockwell HR 15N Rockwell HRC (see 7.3.3.2) As-welded carbon steels, carbon manganese steels and low alloy steels that comply with the hardness requirements of Table A.l do not requ
34、ire post weld heat treatment. Base metal, HAZ and weld root metal as shown in Figure 2, Figure 3 or Figure 4 Base metal and HAZ for weld overlays as shown in Figure 6, see also A.2.1.5 b) Weld cap: Base metal, HAZ and weld metal of unexposed weld cap as shown in Figure 2 or Figure 4 As shown in Figu
35、re 5 Base metal and HAZ for weld overlays as shown in Figure 6, see also A.2.1.5 b) 250 HV 70.6 HR 15N 250 HV 70.6 HR 15N 275 HVa 73.0 HR 15N 22 HRC 22 HRC Tubular products with an SMYS not exceeding 360 MPa (52 ksi) and listed in Table A.2 are acceptable in the as-welded condition. For these produc
36、ts, hardness testing of welding procedures may be waived if agreed by the equipment user. Some tubular products with an SMYS exceeding 360 MPa (52 ksi) (see A.2.2.2) may be acceptable in the as-welded condition if suitable qualified welding procedures are used. The conditions in Table A.l shall be m
37、et. Carbon steel and low alloy steel weldments that do not comply with other paragraphs of this subclause shall be stress-relieved at a minimum temperature of 620 O C (1,150 O F ) after welding. The maximum weld zone hardness, determined in accordance with 7.3, shall be 250 HV (or, subject to the re
38、strictions described in 7.3.3,22 HRC). Welding consumables and procedures that produce a deposit containing more than 1 % nickel are acceptable after successful weld SSC qualification by testing in accordance with Annex B. Page 19, Table A. 1 - Maximum acceptable hardness values for carbon steel, ca
39、rbon manganese steel and low alloy steel welds: Replace Table A.l with the following: Table A1 - Maximum acceptable hardness values for carbon steel, carbon manganese steel and low alloy steel welds Hardness test locations for welding procedure Maximum acceptable qualification hardness Hardness test
40、 methods I I I Weld root: a The maximum shall be 250 HV or 70.6 HR 15N unless - - - - the equipment user agrees the alternative weld cap hardness limit; and the parent material(s) are over 9 mm thick; and the weld cap is not exposed directly to the sour environment; and the escape of hydrogen is not
41、 impeded, e.g. by cathodic protection. Page 19, A.2.1.5 b): Replace A.2.1.5 b) with the following: b) The maximum hardness and final heat-treated condition of the base metal substrate comply with A.2.1.2 and, in the case of welded overlays, A.2.1.4. This requirement may be waived in accordance with
42、NACE MROl75/ISO 151 56-3:2003, A.13.1. The maximum hardness and/or other properties of the weld deposit O NACE InternationalllSO 2005 -All rights reserved 5 -,-,- NACE MROl75/ISO 151 56-2:2003/Cor.l:2005(E) shall comply with the requirements of NACE MROl75/ISO 15156-3 or this part of NACE MROl75/ISO
43、 151 56, as applicable. Page 44, Bibliography: Delete NACE MROl75/ISO 151 56-3:2003, Petroleum and natural gas industries - Materials for use in H$- containing environments in oil and gas production - Pari 3: Cracking-resistant CAs (corrosion-resistant alloys) and other alloys Renumber the remaining
44、 references as appropriate. Add the following references: 32 NACE Standard RP0475, Selection of Metallic Materials to Be Used in All Phases of Water Handling for Injection into Oil-Bearing Formations 33 ASTM E 1 O, Test Method for Brinell Hardness of Metallic Materials 34 ASTM E 18, Test Method for
45、ockwell Hardness and ockwell Superficial Hardness of Metallic Materials 35 ASTM E 92, Test Method for Vickers Hardness of Metallic Materials O NACE InternationalllSO 2005 -All rights reserved 1 N T E R N A T I O N W L INTERNATIONAL STANDARD NACE MROl75/ISO 151 56-3:2003 TECHNICAL CORRIGENDUM 2 Publi
46、shed 2005-09-01 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION MWYHAPOflHA OPrAHU3AU no CTAHflAPTUSWUU ORGANISATION INTERNATIONALE DE NORMALISATION Item No. 21307 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resi
47、stant CRAs (corrosion-resistant alloys) and other alloys TECHNICAL CORRIGENDUM 2 Technical Corrigendum 2 to NACE MROl75/ISO 151 56-3 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries. Page iii, Contents
48、: Replace the title for Annex A with the following: Annex A (normative) Environmental cracking-resistant CRAs and other alloys (including Table A1 - Guide to the use of the materials selection tables of Annex A) ICs 75.1 80.01 Ref. No. NACE MROl75ASO 15156- 3: 2003/Cor.2: 2005( E) ISBN 1-57590-021 -
49、1 O NACE International/ IS0 2005 -All rights reserved Published in the U.S.A. by NACE NACE MROl75/ISO 151 56-3:2003/Cor.2:2005(E) Page 2, Table 1 - List of equipment: Replace Table 1 with the following: Table 1 - List of equipment NACE MR0175iiSO 15156-3 is applicable to materials used for the following equipment Drilling, well construction and well-servicing equipment Wells, including subsurface equipment, gas lift equipment, wellheads and Christmas trees Flowlines, gathering lines, field facilities and field
链接地址:https://www.31doc.com/p-3790814.html