SAE-AS-85449-1-2003-R2007.pdf
《SAE-AS-85449-1-2003-R2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-85449-1-2003-R2007.pdf(3页珍藏版)》请在三一文库上搜索。
1、 AEROSPACE STANDARD CLAMP ASSEMBLY, SADDLE TYPE, CUSHIONED, FUEL AND PETROLEUM BASED HYDRAULIC FLUID AS85449/1 ISSUED 2003-08 REAFFIRMED 2007-07 THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3E FEDERAL SUPPLY CLASS 5340 AS85449/1 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS85449 /4/ FIGURE 1 - CLAMP SAE
2、 Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom,
3、 is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY.
4、 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUM
5、ENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007
6、19:31:08 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD CLAMP ASSEMBLY, SADDLE TYPE, CUSHIONED, FUEL AND PETROLEUM BASED HYDRAULIC FLUID AS85449/1 AS85449/1 SHEET 2 OF 3 TABLE 1 - CLAMP DIMENSIONS BASIC NO. AS85449/1 SIZE CODE /11/ TUBE SIZE C .030 D E .
7、 015 G . 001 R1 R2 .03 T TOLERANCE PER AMS 2242 W .005 Y -10 .625 .493 .625 1.525 .020 .090 .37 .040 .500 .218 -12 .750 .555 .750 1.650 .020 .090 .37 .040 .500 .218 -14 .875 .618 .875 1.775 .020 .090 .37 .040 .500 .218 -16 1.000 .690 1.000 1.958 .030 .109 .50 .050 .625 .250 -18 1.125 .753 1.125 2.08
8、3 .030 .109 .50 .050 .625 .250 -20 1.250 .815 1.250 2.208 .030 .109 .50 .050 .625 .250 -24 1.500 .940 1.500 2.458 .030 .109 .50 .050 .625 .250 -28 1.750 1.065 1.750 2.708 .030 .109 .50 .050 .625 .250 -32 2.000 1.203 2.000 3.016 .030 .125 .50 .063 .750 .250 -36 2.250 1.328 2.250 3.266 .030 .125 .50 .
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 85449 2003 R2007
链接地址:https://www.31doc.com/p-3793287.html