SAE-AS-4388-1991-R2007.pdf
《SAE-AS-4388-1991-R2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-4388-1991-R2007.pdf(21页珍藏版)》请在三一文库上搜索。
1、AEROSPACE STANDARD AS4388 Issued1991-12 Reaffirmed2007-08 Hose Assembly PTFE Heavy Duty, -65 To 400 F (-55 To 204 C) 8000 psi (56 000 kPa) Hydraulic and Pneumatic 1.SCOPE: This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for
2、 use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 F. Gaseous service shall be limited to 150 F. 2.REFERENCES: 2.1Applicable Documents: The following publications form a part of this specification to the extent specified herein. The latest issue of SAE publicatio
3、ns shall apply. The applicable issue of other documents shall be as specified in AMS 2350. 2.1.1SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. AMS 3380Hose, Polytetrafluoroethylene, TFE Fluorocarbon Resin, Wire Braid Reinforced AMS 4928Ti Alloy Bars, Forging
4、s and Rings, 6Al - 4V, Anneal 120,000 psi AMS 4944Ti Alloy Tubing, Seamless Hydraulic 3.0Al - 2.5V Cold-Worked, Stress Relieved AMS 4945Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Texture Controlled, 105,000 psi Yield Strength AMS 4965Ti Alloy Bars, Forgings and Rings, 6Al - 4V, Solution
5、and Precipitation Heat Treated AMS 5536Steel Bars, Corrosion-Resistant, 18Cr - 8.5Ni (SAE 30302) Cold Drawn, 100,000 psi (690 MPa) AMS 5556Steel Tubing, Seamless or Welded, Corrosion and Heat-Resistant 18Cr - 11Ni - (Cb + Ta) (SAE 30347) Hydraulic AMS 5557Steel Tubing, Seamless and Welded, Corrosion
6、 and Heat-Resistant 18Cr - 11Ni-Ti (SAE 30321) Hydraulic RATIONALE This document has been reaffirmed to comply with the SAE 5-Year Review policy. SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of
7、this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or c
8、ancelled. SAE invites your written comments and suggestions. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, w
9、ithout the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicens
10、ee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:38:37 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS4388 - 2 - 2.1.1 (Continued): AMS 5561Steel Tubing Welded and Drawn, 9.0Mn - 20Cr - 6.5Ni - 0.28N, High Pressure Hydraulic AMS 5567Steel Tubing, Seamle
11、ss and Welded, Corrosion-Resistant 19Cr - 10Ni (SAE 30304) Hydraulic, Solution Treated AMS 5570Steel Tubing, Seamless, Corrosion and Heat-Resistant 18Cr - 11Ni - 0.40Ti (SAE 30321) AMS 5571Steel Tubing, Seamless, Corrosion and Heat-Resistant 18Cr - Ni - 0.70 (Cb + Ta) (SAE 30347) AMS 5575Steel Tubin
12、g, Welded, Corrosion and Heat-Resistant 18Cr - 10.5Ni - 0.70 (Cb + Ta) (SAE 30347) AMS 5576Tubing Welded, 18Cr - 10.5Ni - 0.40Ti Solution Heat Treated AMS 5637Steel Bars, Corrosion-Resistant, 18Cr - 10Ni (SAE 30304) AMS 5639Steel Bars, Forgings, Tubing, and Rings, Corrosion-Resistant 19Cr - 10Ni (SA
13、E 30304) AMS 5643Steel Bars, Forgings, Tubing and Rings, Corrosion-Resistant 16.5Cr - 4.0Ni - 4.0Cu AMS 5644Steel Bars and Forgings, Corrosion and Heat-Resistant 17Cr - 7Ni - 1Al AMS 5645Steel Bars, Forgings, Tubing and Rings, Corrosion and Heat-Resistant, 18Cr - 10Ni - 0.40Ti (SAE 30321) AMS 5646St
14、eel Bars, Forgings, Tubing and Rings, Corrosion and Heat-Resistant, 18Cr - 11Ni - 0.60 (Cb + Ta) (SAE 30347) AMS 5647Steel Bars, Forgings, Tubing and Rings, 18Cr - 8Ni AMS 5659Steel Bars, Forgings and Rings, Corrosion-Resistant 15Cr - 4.5Ni - 0.30 (Cb + Ta) - 3.5 Consumable Electrode Melted AMS 5743
15、Steel Bars and Forgings, Corrosion and Moderate Heat-Resistant 15.5Cr - 4.5Ni - 2.9Mo - 0.10N, Solution Heat-Treated, Sub-Zero Cooled, Equalized and Over-Tempered ARP603Impulse Testing of Hydraulic Hose Assemblies, Tubing and Fittings AS611Tetrafluoroethylene Hose Assembly Cleaning Methods AS1055Fir
16、e Resistance and Fire Test ARP1153Method for Determining Relative Specific Gravity, Polytetrafluoroethylene Tubing AIR1228Standard Impulse Machine Equipment and Operation ARP1835Preparation for Delivery, General Requirements for Hose Assemblies AS2078Test Methods, Hose Assemblies PTFE (in process) 2
17、.1.2ASTM Publications: Available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. ASTM A 262Detecting Susceptibility to Intergranular Attack on Stainless Steel ASTM A 313Chrome Nickel Stainless and Heat-Resistant Steel - Spring Wire ASTM D 412Rubber, Determi
18、nation of Tension Characteristics Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:38:37 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS4388 - 3 - 2.1.2 (Continued): ASTM A 580Stain
19、less and Heat-Resistant Steel Wire - Type 304 or 316, Condition B ASTM 644Sodium Chloride Reagent Grade ASTM D 792Specific Gravity and Density of Plastics by Displacement ASTM D 1457TFE - Fluorocarbon Resin Molding and Extrusion Materials 2.1.3U.S. Government Publications: Available from Standardiza
20、tion Document Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. QQ-S-763Steel Bars, Wire Shapes and Forgings, Corrosion-Resisting MIL-F-8815Filter and Filter Elements, Fluid Pressure, Hydraulic Line, 15 Micron Absolute and 5 Micron Absolute, Type ID Systems MIL-F-85720Fitting
21、s, Tube, Fluid Systems, Separable, High Pressure Dynamic MIL-F-85720/1Fittings, Tube, Fluid Systems, Separable, High Pressure, Dynamic Beam Seal, Design Standard for Male End MIL-F-85800Hose Assemblies, Tetrafluoroethylene, Aramid Fiber Reinforced MIL-H-5606Hydraulic Fluid, Petroleum Base, Aircraft,
22、 Missile and Ordnance MIL-H-83282Hydraulic Fluid, Fire-Resistant, Synthetic Hydrocarbon Base Aircraft MIL-L-7808Lubricating Oil, Aircraft Turbine Engine, Synthetic Base MIL-S-8879Screw Threads, Controlled Radius Root with Increased Minor Diameter MIL-T-8504Tubing, Steel, Corrosion-Resisting (304) Ae
23、rospace Vehicle Hydraulic Systems, Annealed, Seamless and Welded MIL-T-8606Tubing, Steel, Corrosion-Resistant (18-8 Stabilized and Extra Low Carbon) MIL-T-8808Tubing, Steel, Corrosion-Resistant (18-8 Stabilized) Aircraft Hydraulic Quality DOD-STD-100Engineering Drawing Practices for Inspection MIL-S
24、TD-105Sampling Procedures and Tables by Attributes MIL-STD-130Identification Marking of U.S. Military Property MIL-STD-831Test Reports, Preparation of MS19059Balls Bearing, Ferrous, Chrome Alloy Steel H4-1Cataloging Handbook (Federal Code Numbers) 3.TECHNICAL REQUIREMENTS: 3.1Qualification: The hose
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 4388 1991 R2007
链接地址:https://www.31doc.com/p-3793290.html