SAE-AS-5002C-2007.pdf
《SAE-AS-5002C-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-5002C-2007.pdf(3页珍藏版)》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING, ELBOW, 90, BEAM SEAL AS5002 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, witho
2、ut the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1996-05 REAFFIRMED 2001-12 REVISED 2007-09 THIRD ANGLE PROJECTION CUS
3、TODIAN: SAE G-3/G-3B REV. C FEDERAL SUPPLY CLASS 4730 AS5002 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: /5/ AS85421, AS85720 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is en
4、tirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE inv
5、ites your written comments and suggestions. RATIONALE TO CORRECT THE DEFINED LEG DIAMETER DIM G. FIGURE 1 - FITTING, ELBOW, 90 TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS5002 /15/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS A A G MIN V W LB/EA MAX CRES LB/EA MAX TI 03 04 05 06 08 10 12
6、 14 16 20 24 .188 .250 .312 .375 .500 .625 .750 .875 1.000 1.250 1.500 .3750-28 UNJS .4375-24 UNJS .5000-24 UNJS .5625-20 UNJS .7188-20 UNJS .8438-18 UNJS 1.0000-16 UNJ 1.1250-16 UNJ 1.2500-14 UNJS 1.5781-14 UNJS 1.8438-14 UNJS .575 .617 .653 .704 .824 .955 1.062 1.216 1.246 1.387 1.688 .285 .329 .3
7、91 .454 .547 .673 .860 1.110 1.110 1.360 1.610 .360- .377 .360- .377 .423- .440 .485- .502 .547- .565 .673- .691 .860- .878 1.110-1.128 1.110-1.128 1.355-1.380 1.605-1.630 .055 .060 .060 .060 .065 .070 .095 .105 .115 .110 .130 .0305 .0341 .0456 .0571 .0782 .119 .192 .372 .335 .496 .824 .0174 .0195 .
8、0261 .0326 .0447 .0680 .110 .213 .191 .283 .471 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:20:51 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, ELBOW, 90
9、, BEAM SEAL AS5002 SHEET 2 OF 3 REV. C NOTES: /1/ MATERIAL: a. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS 4965. b. CODE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS 5643. c. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 5002 2007
链接地址:https://www.31doc.com/p-3793313.html