SAE-AS-39029A-2006.pdf
《SAE-AS-39029A-2006.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-39029A-2006.pdf(92页珍藏版)》请在三一文库上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2006 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)
4、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org AS39029 REV. A AEROSPACE STANDARD Issued 2001-01 Revised 2006-06 Superseding AS39029 (R) Contacts, Electrical Connector, General Specification For RATIONALE The document was totally revised to includes comments recei
5、ved by the government and industry since 1988, incorporate Engineering Position Letter amendments, remove government jargon, update specification references, align specification with SAE guidelines as needed, and review for minor technical problems. 1. SCOPE 1.1 Scope This specification covers the g
6、eneral requirements for removable crimp, solderless wrap, and solder type electrical contacts for use in connectors and other electric and electronic components (see 6.1) with stranded conductor wire. The contacts shall be capable of operating within the temperature range as specified (see 3.1). 1.2
7、 Classification 1.2.1 Part Number and BIN (Basic Identification Number) Code Each contact shall be identified by a non-significant, but distinctive three digit number indicating the BIN code as specified on the applicable specification sheet (see 3.1 and the Appendix A). The part number shall be as
8、specified in the specification sheets (see 3.1). 1.2.2 Class Contacts shall be of the following classes as specified (see 3.1). Class A - Maximum operating temperature +125 C. Class B - Maximum operating temperature +200 C. SAE AS39029 Revision A - 2 - 1.2.3 Type Contacts and bushings shall be of th
9、e types shown in Table 1 as specified (see 3.1). TABLE 1 - CONTACT TYPES Type Material Application/Specification A Copper alloy General Purpose / ASTM B 36, B 121, B 16, B 16M, B 124 or equivalent B Ferrous alloy Hermetic / ASTM B 829 C Nickel-Chromium (formerly Chromel) Nickel-Aluminum/Silicon (for
10、merly Alumel) Copper-Nickel Alloy (formerly Constantan) Iron Copper Thermocouple / ASTM E 230 Type E Thermocouple / ASTM E 230 Type K Thermocouple / ASTM E 230 Type K Thermocouple / ASTM E 230 Type E Thermocouple / ASTM E 230 Type J Thermocouple / ASTM E 230 Type T Thermocouple /ASTM E 230 Type J Th
11、ermocouple /ASTM E 230 Type T D Copper alloy Shielded (including coaxial, twin-axial, and tri-axial) / ASTM B 36, B 121, B 16, B 16M, B 124 1.3 Deletion of Stock Deletion of stock manufactured to a revision letter prior to the revision letter specified in this basic specification and a specification
12、 sheet shall be specified herein and in the specification sheet. 2. APPLICABLE DOCUMENTS 2.1 Government Documents Unless otherwise specified, the latest issue of the following specifications, standards and handbooks form a part of this specification to the extent specified herein. Application for co
13、pies should be addressed to the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. MIL-DTL-22520 Crimping Tools, Terminal, Tool Kits, Hand or Power Actuated, Wire Termination, General Specification for MIL-DTL-55330 Connectors, Electrical and Fiber Op
14、tic, Packaging of MIL-DTL-81381 Wire, Electric, Polyimide-Insulated, Copper or Copper Alloy MS3109 Contact Wire Barrel, Crimp Type MIL-HDBK-454 Department of Defense Handbook, General Guidelines for Electronic Equipment SD-6 Provisions Governing Qualification -,-,- SAE AS39029 Revision A - 3 - 2.2 O
15、ther Publications The following documents form a part of the specification to the extent specified herein. Unless otherwise specified the issues of the documents which are indicated as DoD adopted shall be the issue listed in the current DoDISS and the supplement thereto, if applicable. 2.2.1 Societ
16、y of Automotive Engineers International (SAE) Application for copies should be addressed to: SAE International, 400 Commonwealth Drive, Warrendale, PA 15096- 0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org AIR1351 Manufacturers Identification of Electrical
17、Connector Contacts, Terminals and Splices AS4461 Assembly and Soldering Criteria for High Quality/High Reliability Soldered Wire and Cable Termination in Aerospace Vehicles AS5261 Contact Wire Barrel, Crimp Type AS22759 Wire, Electric, Flouropolymer-Insulated, Copper or Copper Alloy AS31971 Gage Pin
18、 for Socket Contact Engagement Test AS33481 Contact Bushing, Electric, Wire Barrel AMS-P-81728 Plating, Tin-lead (Electro-deposit) AMS-QQ-N-290 Nickel Plating (Electrodeposited) 2.2.1.1 AS39029 Specification Sheets AS39029/1 Contacts, Electrical Connector, Pin, Crimp Removable (For AS81714 Terminal
19、Junction System) AS39029/2 Contacts, Electrical Connector, Pin, Crimp Removable (For AS81659 Series 1 Connectors) AS39029/3 Contacts, Electrical Connector, Socket, Crimp Removable (For AS81659 Series 1 Connectors) AS39029/4 Contacts, Electrical Connector, Pin, Crimp Removable (For MIL-DTL-26482 Seri
20、es 2, AS81703 Series 3, MIL-DTL-83733, and MIL-DTL-83723 Series 3 Connectors) AS39029/5 Contacts, Electrical Connector, Socket, Crimp Removable (For MIL-DTL-26482 Series 2, AS81703 Series 3, MIL-DTL-83733, and MIL-DTL-83723 Series 3 Connectors) AS39029/6 Contacts, Electrical Connector, Pin, Crimp Re
21、movable, Shielded (For MIL-C-81511 Series 1 and 2 Connectors) AS39029/7 Contacts, Electrical Connector, Pin, Crimp Removable, Shielded (For MIL-DTL-26482 Series 2 and AS81703 Series 3 Connectors) AS39029/8 Contacts, Electrical Connector, Socket, Crimp Removable, Shielded (For MIL-DTL-26482 Series 2
22、and AS81703 Series 3 Connectors) AS39029/9 Contacts, Electrical Connector, Pin, Crimp Removable, Thermocouple (For MIL-DTL-26482 Series 2, AS81703 Series 3, MIL-DTL-83723 Series 3, and MIL-DTL-83733 Connectors) -,-,- SAE AS39029 Revision A - 4 - AS39029/10 Contacts, Electrical Connectors, Socket, Cr
23、imp Removable, Thermocouple (For MIL-DTL-26482 Series 2, AS81703 Series 3, MIL-DTL-83723 Series 3, and MIL-DTL-83733 Connectors) AS39029/11 Contacts, Electrical Connector, Pin, Crimp Removable (For AS81659 Series 2 Connectors) AS39029/12 Contacts, Electrical Connector, Socket, Crimp Removable (For A
24、S81659 Series 2 Connectors) AS39029/13 Contacts, Electrical Connector, Socket, Crimp Removable, Shielded (For MIL-C-81511 Series 1 Connectors) AS39029/14 Contacts, Electrical Connector, Socket, Crimp Removable, Shielded (For MIL-C-81511 Series 2 Connectors) AS39029/16 Contacts, Electrical Connector,
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 39029 2006
链接地址:https://www.31doc.com/p-3793317.html