SAE-AS-8021-2008.pdf
《SAE-AS-8021-2008.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-8021-2008.pdf(9页珍藏版)》请在三一文库上搜索。
1、AEROSPACE STANDARD AS8021 Issued1981-03 Reaffirmed 2008-02 Minimum Performance Standard for Direction Instrument, Non-Magnetic (Gyroscopically Stabilized) 1.PURPOSE: This Aerospace Standard (AS) defines minimum performance requirements under standard and environmental conditions for Gyroscopically S
2、tabilized Non-Magnetic Direction Instruments for use in aircraft. 2.SCOPE: This document establishes the minimum requirements for design and qualification of equipment identified as Gyroscopically Stabilized Non-Magnetic Direction Instruments. 3.GENERAL REQUIREMENTS: 3.1Operation of Controls: The op
3、eration of controls intended for use during flight, if any, in all possible position combinations and sequences shall not result in a condition whose presence or continuation would be detrimental to the continued performance of the equipment. 3.2Accessibility of Controls: Controls which are not norm
4、ally adjusted in flight shall not be readily accessible to flight personnel, when the equipment is installed in accordance with the manufacturers instructions. 3.3Compatibility of Components: If the equipment components require matching for proper operation, they shall be identified in a manner that
5、 will provide for proper matching. The instructions furnished by the manufacturer must contain data detailing these limitations. SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is en
6、tirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE inv
7、ites your written comments and suggestions. Copyright 2008 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
8、written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE AS8021 - 2 - 3.4Fire Resistance: Except for small parts (such as knobs, fasteners, se
9、als, grommets and small electrical parts) that would not contribute significantly to the propagation of a fire, all materials must be self-extinguishing when tested in accordance with the requirements of Federal Aviation Regulation 25.1359 (d) and Appendix F thereto, with paragraph (b) of Appendix F
10、 or may be configured as used. 3.5Interchangeability: Instruments and components which are identified with the same manufacturers part number shall be interchangeable. 3.6Malfunction Indication: Integral means shall be provided to indicate failures and/or the existence of the following conditions: (
11、a)Gyro in fast erection mode, required of electrical instruments except manually caged indicators with automatic release. (b)Gyro operating at speed below the minimum designated by the manufacturer for the instrument to meet the performance requirements herein. The requirement applies to electrical
12、and remotely operated instruments. Additionally, the indicator or display of the repeating or remote indicating type of gyroscopically stabilized instrument shall be provided with means to indicate the following failures: (c)Loss of synchro excitation (d)A mechanical obstruction in the indicator dia
13、l drive mechanism (e)Primary power loss to the indicator or display (f)Servo Amplifier power loss (g)Electrical failure in the servo drive motor phases The indicating means shall indicate the failure or malfunction in a positive and conspicuous manner. 3.7Instrument Cover Glass Reflectance: The tota
14、l reflectance of the instrument cover glass including the integral lighting wedge, if applicable, shall not exceed 10 percent of the incident light. This reflectance applies over the visible light spectrum from 450 nanometers to 600 nanometers, and over an incident solid angle of 60 degrees perpendi
15、cular to the viewing plane. SAE AS8021 - 3 - 3.8Indicating Method: One of the following methods of indication shall be employed: Method IRotating dial display with fixed datum line. The line shall rotate counter-clockwise for right turns. Method II Horizontal scale display with fixed datum line. The
16、 graduations shall move to the left for right turns. 3.9Operating Limits: The instrument shall indicate heading throughout the 360 degree scale range. During dives, climbs, and banks of up to at least 55 degree displacement from level attitude, the instrument shall remain functional; however, the he
17、ading error involved through the gimbal system need not be corrected. 3.10 Dial Markings: 3.10.1 Graduations: The indicators shall be provided with degree graduations at intervals not to exceed five (5) degrees, with major graduations every ten (10) degrees and with numerals at intervals not greater
18、 than 30 degrees, except that the 0, 90, 180, and 270 degrees positions may be marked N, E, S, and W, respectively. 3.10.2 Visibility: Index and dial markings shall be visible from any point within the upper half of a frustum of a cone, the side of which makes an angle of at least 30 degrees with th
19、e perpendicular to the dial and the small diameter of which is the aperture of the instrument case. At least two numerals shall be simultaneously visible. 3.11 Caging Provisions: Unless the gyro assembly has restricted freedom of operation in the pitch and roll axes, a means shall be provided for ca
20、ging and/or releveling the gyro. A means shall be provided to indicate when the gyro is caged, except when it is not possible to leave the gyro in the caged condition. 3.12 Course Setting Provisions: A means shall be provided for manually setting the directional indicator to any heading desired. -,-
21、,- SAE AS8021 - 4 - 4.MINIMUM PERFORMANCE REQUIREMENTS UNDER STANDARD TEST CONDITIONS: 4.1Starting: Rated instrument performance rotor speed shall be achieved within three minutes after normal power is applied for both air and electric operated instruments. By application of 50 percent of rated vacu
22、um or pressure for air operated instruments and 80 percent of rated voltage for electrically operated instruments, the gyro rotor shall start and continue to rotate. If the instrument incorporates a gyro speed monitoring device which provides a positive indication when the gyro speed is below that n
23、ecessary to meet instrument performance, the starting time may exceed three minutes, but shall not be greater than five minutes. 4.2Roll, Pitch and Yaw: The instrument shall be mounted on a test platform which is adjusted to oscillate in roll, pitch and yaw, with a total amplitude of 3 degrees about
24、 each axis, at a frequency of 5 to 7 oscillations per minute while reversing the direction of rotation every 6 revolutions. With the platform level, and the gyro operating at equilibrium speed and uncaged, the dial reading shall be noted. The platform shall then be started in its roll, pitch and yaw
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 8021 2008
链接地址:https://www.31doc.com/p-3793329.html