SAE-AS-5309A-2007.pdf
《SAE-AS-5309A-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-5309A-2007.pdf(4页珍藏版)》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING END, SPHERICAL, 37 FLARED TUBE CONNECTION DESIGN STANDARD AS5309 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocop
2、ying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-10 REAFFIRMED 2001-12 REVISE
3、D 2007-11 THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV. A FEDERAL SUPPLY CLASS 4730 AS5309 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use
4、of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, o
5、r cancelled. SAE invites your written comments and suggestions. RATIONALE THIS STANDARD IS BEING REVISED TO ADD METRIC EQUIVALENT DIMENSIONS. 2X 45 5 J T M ACD A (S) /2/ B A (N) R W /3/ P C SEALING SURFACE TO DEPTH J .020 0.51 .005 0.13 3X R VIEW A ENLARGED 63 1.6 C .005 0.127A .005 0.127A .005 0.12
6、7A FIGURE 1 - FITTING END, STYLE G Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:36:28 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING END, SPHERICAL, 37 FLAR
7、ED TUBE CONNECTION DESIGN STANDARD AS5309 SHEET 2 OF 4 REV. A SEALING SURFACE J K MINF .031 0.79 .016 0.41 R 63 1.6 .005 0.127A .005 0.127 A FIGURE 2 - FITTING END, STYLE E SAME AS STYLE G EXCEPT AS SHOWN TABLE 1A - DIMENSIONS A-D, INCH -POUND UNITS (IN) BASIC NO. AS5309 /10/ SIZE CODE (NOMINAL TUBE
8、 SIZE) T THREAD PER AS8879 A B +.015 -.000 C D 03 .188 .3750-24 UNJF-3A .104 - .114 .174 .277 .129 04 .250 .4375-20 UNJF-3A .168 - .175 .189 .355 .190 05 .312 .5000-20 UNJF-3A .230 - .237 .189 .415 .255 06 .375 .5625-18 UNJF-3A .293 - .301 .193 .470 .320 08 .500 .7500-16 UNJF-3A .387 - .395 .247 .65
9、0 .425 10 .625 .8750-14 UNJF-3A .480 - .488 .261 .760 .540 12 .750 1.0625-12 UNJ-3A .604 - .614 .307 .930 .665 16 1.000 1.3125-12 UNJ-3A .839 - .851 .308 1.180 .915 20 1.250 1.6250-12 UNJ-3A 1.073 - 1.086 .356 1.495 1.145 24 1.500 1.8750-12 UNJ-3A 1.307 - 1.320 .369 1.745 1.380 Copyright SAE Interna
10、tional Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:36:28 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING END, SPHERICAL, 37 FLARED TUBE CONNECTION DESIGN STANDARD AS5309 SHEET 3 OF 4 R
11、EV. A TABLE 1B - DIMENSIONS F-W, INCH -POUND UNITS (IN) BASIC NO. AS5309 /10/ SIZE CODE F +.002 -.003 J .015 K M +.015 -.000 N P S /2/ W 03 .312 .479 .595 .063 .160 .217 .075 .312 04 .364 .550 .658 .075 .126 .219 .067 .312 05 .426 .550 .720 .075 .096 .217 .064 .312 06 .481 .556 .782 .083 .060 .223 .
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 5309 2007
链接地址:https://www.31doc.com/p-3793434.html