SAE-AS-5039-2007.pdf
《SAE-AS-5039-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-5039-2007.pdf(3页珍藏版)》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING, BODY END - THREADED COUPLING, RIGID, SELF-BONDING, DESIGN STANDARD AS5039 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical
2、, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2007-07 THIRD ANGLE PRO
3、JECTION CUSTODIAN: SAE G-3/G-3A FEDERAL SUPPLY CLASS 4730 AS5039 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: NONE /1/ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntar
4、y, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your writt
5、en comments and suggestions. RATIONALE THIS DESIGN STANDARD PROVIDES THE DIMENSIONAL REQUIREMENTS FOR AS1730 FITTING ENDS. FIGURE 1 - FITTING END DESIGN, STYLE A FIGURE 2 - FITTING END DESIGN, STYLE B SAME AS STYLE A EXCEPT AS SHOWN Copyright SAE International Provided by IHS under license with SAEL
6、icensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 21:04:46 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, BODY END - THREADED COUPLING, RIGID, SELF-BONDING, DESIGN STANDARD AS5039 AS5039 SHEET 2 OF 3 TABLE 1 - DIMENSIONS BASIC NO.
7、 AS5039 /10/ SIZE CODE NOM TUBE SIZE REF A .0025 /8/ B .0025 C D E F F TOL. G .010H J .010K L T THREAD MOD PER FED-STD-H28/2 /8/ MAJOR DIA A MOD O-RING SIZE DASH NO. /9/ 04 .250 .6825 .5315 .485 .293 .204 .567 .005 .045 .290 .234 .380 .563 .6875-12 UN-2A 012 05 .312 .7455 .5825 .540 .348 .267 .629 .
8、005 .045 .353 .234 .380 .625 .7500-12 UN-2A 013 06 .375 .8075 .6375 .595 .403 .329 .692 .005 .045 .415 .234 .380 .688 .8125-12 UN-2A 014 08 .500 .9325 .7645 .721 .529 .454 .817 .005 .045 .540 .234 .380 .813 .9375-12 UN-2A 016 10 .625 1.0575 .9025 .855 .663 .579 .942 .005 .045 .665 .250 .396 .938 1.0
9、625-12 UN-2A 018 12 .750 1.2455 1.0355 .989 .797 .704 1.124 .010 .045 .790 .250 .396 1.125 1.2500-12 UNF-2A020 16 1.000 1.4955 1.2865 1.240 1.048 .940 1.374 .010 .045 1.040 .250 .396 1.375 1.5000-12 UNF-2A024 20 1.250 1.7455 1.5365 1.490 1.298 1.190 1.624 .010 .045 1.290 .250 .396 1.625 1.7500-12 UN
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 5039 2007
链接地址:https://www.31doc.com/p-3793457.html